Перейти до

feebsd 8 pppoed и адсл

Starnet

Автор: Starnet,
в Софт

 Share Подписчики 0

Рекомендованные сообщения

Starnet

Starnet 4

Опубликовано:
Опубликовано:

Здравствуйте.

Поднимаю pppoe соединение через адсл модем. Конектиться вроде без ошибок. Получаю много айпи о провайдера. Не могу поянть в чом трабл. Может кто-то с таким сталкивался?

конфиг ppp.conf

default:

set log Phase tun command # you can add more detailed logging if you wish

 

 

adsl:

set device PPPoE:rl1 # replace xl1 with your Ethernet device

set authname my login

set authkey my pass

set mru 1492

set mtu 1492

set ctsrts off

enable lqr

set timeout 0

set readial 0 0

add default HISADDR

 

после запуска ppp -ddial adsl

получаем

tun0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> metric 0 mtu 1500

options=80000<LINKSTATE>

inet 178.94.39.151 --> 195.5.5.204 netmask 0xffffffff

inet 178.94.96.112 --> 195.5.5.204 netmask 0xffffffff

inet 178.94.47.118 --> 195.5.5.204 netmask 0xffffffff

inet 178.94.144.31 --> 195.5.5.204 netmask 0xffffffff

Opened by PID 22883

 

на интервейсе tun0 не один апишник а несколько! и так может быть хоть 100 ip если не убить ppp. В чом трабл?

ppp.log

 

Feb 12 21:06:58 billing ppp[22882]: Phase: Using interface: tun0

Feb 12 21:06:58 billing ppp[22882]: Phase: deflink: Created in closed state

Feb 12 21:06:58 billing ppp[22882]: tun0: Command: adsl: set device PPPoE:rl1

Feb 12 21:06:58 billing ppp[22882]: tun0: Command: adsl: set authname my login

Feb 12 21:06:58 billing ppp[22882]: tun0: Command: adsl: set authkey ********

Feb 12 21:06:58 billing ppp[22882]: tun0: Command: adsl: set mru 1492

Feb 12 21:06:58 billing ppp[22882]: tun0: Command: adsl: set mtu 1492

Feb 12 21:06:58 billing ppp[22882]: tun0: Command: adsl: set ctsrts off

Feb 12 21:06:58 billing ppp[22882]: tun0: Command: adsl: enable lqr

Feb 12 21:06:58 billing ppp[22882]: tun0: Command: adsl: set timeout 0

Feb 12 21:06:58 billing ppp[22882]: tun0: Command: adsl: set redial 0 0

Feb 12 21:06:58 billing ppp[22882]: tun0: Command: adsl: nat enable no

Feb 12 21:06:58 billing ppp[22883]: tun0: Phase: PPP Started (ddial mode).

Feb 12 21:06:58 billing ppp[22883]: tun0: Phase: bundle: Establish

Feb 12 21:06:58 billing ppp[22883]: tun0: Phase: deflink: closed -> opening

Feb 12 21:06:58 billing ppp[22883]: tun0: Phase: deflink: Connected!

Feb 12 21:06:58 billing ppp[22883]: tun0: Phase: deflink: opening -> dial

Feb 12 21:06:58 billing ppp[22883]: tun0: Phase: deflink: dial -> carrier

Feb 12 21:07:03 billing ppp[22883]: tun0: Phase: deflink: Disconnected!

Feb 12 21:07:03 billing ppp[22883]: tun0: Phase: deflink: carrier -> hangup

Feb 12 21:07:03 billing ppp[22883]: tun0: Phase: deflink: Connect time: 5 secs: 0 octets in, 0 octets out

Feb 12 21:07:03 billing ppp[22883]: tun0: Phase: deflink: 0 packets in, 0 packets out

Feb 12 21:07:03 billing ppp[22883]: tun0: Phase: total 0 bytes/sec, peak 0 bytes/sec on Sat Feb 12 21:06:58 2011

Feb 12 21:07:03 billing ppp[22883]: tun0: Phase: deflink: hangup -> opening

Feb 12 21:07:03 billing ppp[22883]: tun0: Phase: deflink: Enter pause (0) for redialing.

Feb 12 21:07:03 billing ppp[22883]: tun0: Phase: deflink: Connected!

Feb 12 21:07:03 billing ppp[22883]: tun0: Phase: deflink: opening -> dial

Feb 12 21:07:03 billing ppp[22883]: tun0: Phase: deflink: dial -> carrier

Feb 12 21:07:06 billing ppp[22883]: tun0: Phase: Received NGM_PPPOE_ACNAME (hook "KV-JE-R2")

Feb 12 21:07:06 billing ppp[22883]: tun0: Phase: Received NGM_PPPOE_SESSIONID

Feb 12 21:07:06 billing ppp[22883]: tun0: Phase: Received NGM_PPPOE_SUCCESS

Feb 12 21:07:06 billing ppp[22883]: tun0: Phase: deflink: carrier -> login

Feb 12 21:07:06 billing ppp[22883]: tun0: Phase: deflink: login -> lcp

Feb 12 21:07:07 billing ppp[22883]: tun0: Phase: bundle: Authenticate

Feb 12 21:07:07 billing ppp[22883]: tun0: Phase: deflink: his = PAP, mine = none

Feb 12 21:07:07 billing ppp[22883]: tun0: Phase: Pap Output: my login ********

Feb 12 21:07:07 billing ppp[22883]: tun0: Phase: Pap Input: SUCCESS ()

Feb 12 21:07:07 billing ppp[22883]: tun0: Phase: deflink: lcp -> open

Feb 12 21:07:07 billing ppp[22883]: tun0: Phase: bundle: Network

Feb 12 21:07:08 billing ppp[22883]: tun0: Phase: deflink: IPV6CP protocol reject closes IPV6CP !

Feb 12 21:07:08 billing ppp[22883]: tun0: Phase: deflink: IPV6CP protocol reject closes IPV6CP !

Feb 12 21:07:08 billing ppp[22883]: tun0: Warning: iface add: ioctl(SIOCAIFADDR, 178.94.39.151 -> 195.5.5.204): File exists

Feb 12 21:07:08 billing ppp[22883]: tun0: Error: ipcp_InterfaceUp: unable to set ip address

Feb 12 21:07:11 billing ppp[22883]: tun0: Phase: deflink: IPV6CP protocol reject closes IPV6CP !

Feb 12 21:07:20 billing last message repeated 3 times

Feb 12 21:07:23 billing ppp[22883]: tun0: Phase: bundle: Terminate

Feb 12 21:07:23 billing ppp[22883]: tun0: Phase: deflink: open -> lcp

Feb 12 21:07:23 billing ppp[22883]: tun0: Phase: deflink: Disconnected!

Feb 12 21:07:23 billing ppp[22883]: tun0: Phase: deflink: lcp -> logout

Feb 12 21:07:23 billing ppp[22883]: tun0: Phase: deflink: logout -> hangup

Feb 12 21:07:23 billing ppp[22883]: tun0: Phase: deflink: Disconnected!

Feb 12 21:07:23 billing ppp[22883]: tun0: Phase: deflink: Connect time: 20 secs: 227 octets in, 244 octets out

Feb 12 21:07:23 billing ppp[22883]: tun0: Phase: deflink: 17 packets in, 17 packets out

Feb 12 21:07:23 billing ppp[22883]: tun0: Phase: total 23 bytes/sec, peak 81 bytes/sec on Sat Feb 12 21:07:11 2011

Feb 12 21:07:23 billing ppp[22883]: tun0: Phase: deflink: hangup -> opening

Feb 12 21:07:23 billing ppp[22883]: tun0: Phase: bundle: Establish

Feb 12 21:07:23 billing ppp[22883]: tun0: Phase: deflink: Enter pause (3) for redialing.

Feb 12 21:07:26 billing ppp[22883]: tun0: Phase: deflink: Connected!

Feb 12 21:07:26 billing ppp[22883]: tun0: Phase: deflink: opening -> dial

Feb 12 21:07:26 billing ppp[22883]: tun0: Phase: deflink: dial -> carrier

Feb 12 21:07:29 billing ppp[22883]: tun0: Phase: Received NGM_PPPOE_ACNAME (hook "KV-JE-R2")

Feb 12 21:07:29 billing ppp[22883]: tun0: Phase: Received NGM_PPPOE_SESSIONID

Feb 12 21:07:29 billing ppp[22883]: tun0: Phase: Received NGM_PPPOE_SUCCESS

Feb 12 21:07:29 billing ppp[22883]: tun0: Phase: deflink: carrier -> login

Feb 12 21:07:29 billing ppp[22883]: tun0: Phase: deflink: login -> lcp

Feb 12 21:07:30 billing ppp[22883]: tun0: Phase: bundle: Authenticate

Feb 12 21:07:30 billing ppp[22883]: tun0: Phase: deflink: his = PAP, mine = none

Feb 12 21:07:30 billing ppp[22883]: tun0: Phase: Pap Output: my login ********

Feb 12 21:07:30 billing ppp[22883]: tun0: Phase: Pap Input: SUCCESS ()

Feb 12 21:07:30 billing ppp[22883]: tun0: Phase: deflink: lcp -> open

Feb 12 21:07:30 billing ppp[22883]: tun0: Phase: bundle: Network

Feb 12 21:07:30 billing ppp[22883]: tun0: Phase: deflink: IPV6CP protocol reject closes IPV6CP !

Feb 12 21:07:30 billing ppp[22883]: tun0: Phase: deflink: IPV6CP protocol reject closes IPV6CP !

Feb 12 21:07:30 billing ppp[22883]: tun0: Warning: iface add: ioctl(SIOCAIFADDR, 178.94.96.112 -> 195.5.5.204): File exists

Feb 12 21:07:30 billing ppp[22883]: tun0: Error: ipcp_InterfaceUp: unable to set ip address

Feb 12 21:07:33 billing ppp[22883]: tun0: Phase: deflink: IPV6CP protocol reject closes IPV6CP !

Feb 12 21:07:42 billing last message repeated 3 times

Feb 12 21:07:45 billing ppp[22883]: tun0: Phase: bundle: Terminate

Feb 12 21:07:45 billing ppp[22883]: tun0: Phase: deflink: open -> lcp

Feb 12 21:07:45 billing ppp[22883]: tun0: Phase: deflink: Disconnected!

Feb 12 21:07:45 billing ppp[22883]: tun0: Phase: deflink: lcp -> logout

Feb 12 21:07:45 billing ppp[22883]: tun0: Phase: deflink: logout -> hangup

Feb 12 21:07:45 billing ppp[22883]: tun0: Phase: deflink: Disconnected!

Feb 12 21:07:45 billing ppp[22883]: tun0: Phase: deflink: Connect time: 19 secs: 227 octets in, 244 octets out

Feb 12 21:07:45 billing ppp[22883]: tun0: Phase: deflink: 34 packets in, 34 packets out

Feb 12 21:07:45 billing ppp[22883]: tun0: Phase: total 24 bytes/sec, peak 81 bytes/sec on Sat Feb 12 21:07:34 2011

Feb 12 21:07:45 billing ppp[22883]: tun0: Phase: deflink: hangup -> opening

Feb 12 21:07:45 billing ppp[22883]: tun0: Phase: bundle: Establish

Feb 12 21:07:45 billing ppp[22883]: tun0: Phase: deflink: Enter pause (3) for redialing.

Feb 12 21:07:48 billing ppp[22883]: tun0: Phase: deflink: Connected!

Feb 12 21:07:48 billing ppp[22883]: tun0: Phase: deflink: opening -> dial

Feb 12 21:07:48 billing ppp[22883]: tun0: Phase: deflink: dial -> carrier

Feb 12 21:07:51 billing ppp[22883]: tun0: Phase: Received NGM_PPPOE_ACNAME (hook "KV-JE-R2")

Feb 12 21:07:51 billing ppp[22883]: tun0: Phase: Received NGM_PPPOE_SESSIONID

Feb 12 21:07:51 billing ppp[22883]: tun0: Phase: Received NGM_PPPOE_SUCCESS

Feb 12 21:07:51 billing ppp[22883]: tun0: Phase: deflink: carrier -> login

Feb 12 21:07:51 billing ppp[22883]: tun0: Phase: deflink: login -> lcp

Feb 12 21:07:52 billing ppp[22883]: tun0: Phase: bundle: Authenticate

Feb 12 21:07:52 billing ppp[22883]: tun0: Phase: deflink: his = PAP, mine = none

Feb 12 21:07:52 billing ppp[22883]: tun0: Phase: Pap Output: my login ********

Feb 12 21:07:53 billing ppp[22883]: tun0: Phase: Pap Input: SUCCESS ()

Feb 12 21:07:53 billing ppp[22883]: tun0: Phase: deflink: lcp -> open

Feb 12 21:07:53 billing ppp[22883]: tun0: Phase: bundle: Network

Feb 12 21:07:53 billing ppp[22883]: tun0: Phase: deflink: IPV6CP protocol reject closes IPV6CP !

Feb 12 21:07:53 billing ppp[22883]: tun0: Phase: deflink: IPV6CP protocol reject closes IPV6CP !

Feb 12 21:07:53 billing ppp[22883]: tun0: Warning: iface add: ioctl(SIOCAIFADDR, 178.94.47.118 -> 195.5.5.204): File exists

Feb 12 21:07:53 billing ppp[22883]: tun0: Error: ipcp_InterfaceUp: unable to set ip address

Feb 12 21:07:56 billing ppp[22883]: tun0: Phase: deflink: IPV6CP protocol reject closes IPV6CP !

Feb 12 21:08:05 billing last message repeated 3 times

Feb 12 21:08:08 billing ppp[22883]: tun0: Phase: bundle: Terminate

Feb 12 21:08:08 billing ppp[22883]: tun0: Phase: deflink: open -> lcp

Feb 12 21:08:08 billing ppp[22883]: tun0: Phase: deflink: Disconnected!

Feb 12 21:08:08 billing ppp[22883]: tun0: Phase: deflink: lcp -> logout

Feb 12 21:08:08 billing ppp[22883]: tun0: Phase: deflink: logout -> hangup

Feb 12 21:08:08 billing ppp[22883]: tun0: Phase: deflink: Disconnected!

Feb 12 21:08:08 billing ppp[22883]: tun0: Phase: deflink: Connect time: 20 secs: 227 octets in, 244 octets out

Feb 12 21:08:08 billing ppp[22883]: tun0: Phase: deflink: 51 packets in, 51 packets out

Feb 12 21:08:08 billing ppp[22883]: tun0: Phase: total 23 bytes/sec, peak 81 bytes/sec on Sat Feb 12 21:07:56 2011

Feb 12 21:08:08 billing ppp[22883]: tun0: Phase: deflink: hangup -> opening

Feb 12 21:08:08 billing ppp[22883]: tun0: Phase: bundle: Establish

Feb 12 21:08:08 billing ppp[22883]: tun0: Phase: deflink: Enter pause (3) for redialing.

Ссылка на сообщение
Поделиться на других сайтах
roneaf

roneaf 2

Опубліковано:
Опубліковано:

Я только начинающий пользователь *nix н у меня на FreeBSD 8.0 работает такой конфиг

inet:
set device PPPoE:em0:1
set authname 1
set authkey 1
set dial
set login
set openmode active
set mppe 128 stateful
set timeout 180
set redial 0 0
disable ipv6cp
disable ipv6
disable pred1
deny pred1
disable lqr
deny lqr
add default HISADDR

Ссылка на сообщение
Поделиться на других сайтах
natiss

natiss 16

Опубліковано:
Опубліковано:

http://myfreebsd.ru/network/pppoe-klient-user-levelpppoe:

 

set log Phase Chat LCP IPCP CCP tun command
ident user-ppp VERSION (built COMPILATIONDATE)
set device PPPoE:fxp0  # указываем интерфейс (физический или vlan) к которому подключен провайдер
set speed sync
set mru 1492
set mtu 1492
set ctsrts off
enable lqr
add default HISADDR  #  добавляем маршрут по умолчанию
set dns 8.8.8.8  # устанавливаем DNS (можно указывать Google)
set authname  username # логин
set authkey  passwd  # пароль
[b]set dial
set login[/b]

Ссылка на сообщение
Поделиться на других сайтах
natiss

natiss 16

Опубліковано:
Опубліковано:

Ну или так

 

/usr/local/sbin/mpd5 -d /usr/local/etc/mpd5-ut -p /var/run/mpd5-ut.pid -b

 

 

# cat /usr/local/etc/mpd5-ut/mpd.conf | less
startup:
       # configure mpd users
       set user foo bar admin
       set user foo1 bar1
       # configure the console
       set console self 127.0.0.1 5007
       set console open


default:
       load ut


ut:
#
# PPPoE client: only outgoing calls, auto reconnect,
# ipcp-negotiated address, one-sided authentication,
# default route points on ISP's end
#

       create bundle static B1
      set iface route default
       set ipcp ranges 0.0.0.0/0 0.0.0.0/0

       create link static L1 pppoe
       set link action bundle B1
       set auth authname bdsmbsdm999@dsl.ukrtel.net
       set auth password harDcOre
       set link max-redial 0
       set link mtu 1460
       set link keep-alive 10 60
       set pppoe iface ed0
       set pppoe service ""
       open

Ссылка на сообщение
Поделиться на других сайтах

Создайте аккаунт или войдите в него для комментирования

Вы должны быть пользователем, чтобы оставить комментарий

Создать аккаунт

Зарегистрируйтесь для получения аккаунта. Это просто!

Зарегистрировать аккаунт

Вхід

Уже зарегистрированы? Войдите здесь.

Войти сейчас
 Share
Подписчики 0
Перейти до переліку тем

  • Зараз на сторінці   0 користувачів

    Немає користувачів, що переглядають цю сторінку.

×
×
  • Створити нове...