Jump to content

feebsd 8 pppoed и адсл

Starnet

By Starnet,
in Software

 Share Followers 0

Recommended Posts

Starnet

Starnet 4

Posted
Posted

Здравствуйте.

Поднимаю pppoe соединение через адсл модем. Конектиться вроде без ошибок. Получаю много айпи о провайдера. Не могу поянть в чом трабл. Может кто-то с таким сталкивался?

конфиг ppp.conf

default:

set log Phase tun command # you can add more detailed logging if you wish

 

 

adsl:

set device PPPoE:rl1 # replace xl1 with your Ethernet device

set authname my login

set authkey my pass

set mru 1492

set mtu 1492

set ctsrts off

enable lqr

set timeout 0

set readial 0 0

add default HISADDR

 

после запуска ppp -ddial adsl

получаем

tun0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> metric 0 mtu 1500

options=80000<LINKSTATE>

inet 178.94.39.151 --> 195.5.5.204 netmask 0xffffffff

inet 178.94.96.112 --> 195.5.5.204 netmask 0xffffffff

inet 178.94.47.118 --> 195.5.5.204 netmask 0xffffffff

inet 178.94.144.31 --> 195.5.5.204 netmask 0xffffffff

Opened by PID 22883

 

на интервейсе tun0 не один апишник а несколько! и так может быть хоть 100 ip если не убить ppp. В чом трабл?

ppp.log

 

Feb 12 21:06:58 billing ppp[22882]: Phase: Using interface: tun0

Feb 12 21:06:58 billing ppp[22882]: Phase: deflink: Created in closed state

Feb 12 21:06:58 billing ppp[22882]: tun0: Command: adsl: set device PPPoE:rl1

Feb 12 21:06:58 billing ppp[22882]: tun0: Command: adsl: set authname my login

Feb 12 21:06:58 billing ppp[22882]: tun0: Command: adsl: set authkey ********

Feb 12 21:06:58 billing ppp[22882]: tun0: Command: adsl: set mru 1492

Feb 12 21:06:58 billing ppp[22882]: tun0: Command: adsl: set mtu 1492

Feb 12 21:06:58 billing ppp[22882]: tun0: Command: adsl: set ctsrts off

Feb 12 21:06:58 billing ppp[22882]: tun0: Command: adsl: enable lqr

Feb 12 21:06:58 billing ppp[22882]: tun0: Command: adsl: set timeout 0

Feb 12 21:06:58 billing ppp[22882]: tun0: Command: adsl: set redial 0 0

Feb 12 21:06:58 billing ppp[22882]: tun0: Command: adsl: nat enable no

Feb 12 21:06:58 billing ppp[22883]: tun0: Phase: PPP Started (ddial mode).

Feb 12 21:06:58 billing ppp[22883]: tun0: Phase: bundle: Establish

Feb 12 21:06:58 billing ppp[22883]: tun0: Phase: deflink: closed -> opening

Feb 12 21:06:58 billing ppp[22883]: tun0: Phase: deflink: Connected!

Feb 12 21:06:58 billing ppp[22883]: tun0: Phase: deflink: opening -> dial

Feb 12 21:06:58 billing ppp[22883]: tun0: Phase: deflink: dial -> carrier

Feb 12 21:07:03 billing ppp[22883]: tun0: Phase: deflink: Disconnected!

Feb 12 21:07:03 billing ppp[22883]: tun0: Phase: deflink: carrier -> hangup

Feb 12 21:07:03 billing ppp[22883]: tun0: Phase: deflink: Connect time: 5 secs: 0 octets in, 0 octets out

Feb 12 21:07:03 billing ppp[22883]: tun0: Phase: deflink: 0 packets in, 0 packets out

Feb 12 21:07:03 billing ppp[22883]: tun0: Phase: total 0 bytes/sec, peak 0 bytes/sec on Sat Feb 12 21:06:58 2011

Feb 12 21:07:03 billing ppp[22883]: tun0: Phase: deflink: hangup -> opening

Feb 12 21:07:03 billing ppp[22883]: tun0: Phase: deflink: Enter pause (0) for redialing.

Feb 12 21:07:03 billing ppp[22883]: tun0: Phase: deflink: Connected!

Feb 12 21:07:03 billing ppp[22883]: tun0: Phase: deflink: opening -> dial

Feb 12 21:07:03 billing ppp[22883]: tun0: Phase: deflink: dial -> carrier

Feb 12 21:07:06 billing ppp[22883]: tun0: Phase: Received NGM_PPPOE_ACNAME (hook "KV-JE-R2")

Feb 12 21:07:06 billing ppp[22883]: tun0: Phase: Received NGM_PPPOE_SESSIONID

Feb 12 21:07:06 billing ppp[22883]: tun0: Phase: Received NGM_PPPOE_SUCCESS

Feb 12 21:07:06 billing ppp[22883]: tun0: Phase: deflink: carrier -> login

Feb 12 21:07:06 billing ppp[22883]: tun0: Phase: deflink: login -> lcp

Feb 12 21:07:07 billing ppp[22883]: tun0: Phase: bundle: Authenticate

Feb 12 21:07:07 billing ppp[22883]: tun0: Phase: deflink: his = PAP, mine = none

Feb 12 21:07:07 billing ppp[22883]: tun0: Phase: Pap Output: my login ********

Feb 12 21:07:07 billing ppp[22883]: tun0: Phase: Pap Input: SUCCESS ()

Feb 12 21:07:07 billing ppp[22883]: tun0: Phase: deflink: lcp -> open

Feb 12 21:07:07 billing ppp[22883]: tun0: Phase: bundle: Network

Feb 12 21:07:08 billing ppp[22883]: tun0: Phase: deflink: IPV6CP protocol reject closes IPV6CP !

Feb 12 21:07:08 billing ppp[22883]: tun0: Phase: deflink: IPV6CP protocol reject closes IPV6CP !

Feb 12 21:07:08 billing ppp[22883]: tun0: Warning: iface add: ioctl(SIOCAIFADDR, 178.94.39.151 -> 195.5.5.204): File exists

Feb 12 21:07:08 billing ppp[22883]: tun0: Error: ipcp_InterfaceUp: unable to set ip address

Feb 12 21:07:11 billing ppp[22883]: tun0: Phase: deflink: IPV6CP protocol reject closes IPV6CP !

Feb 12 21:07:20 billing last message repeated 3 times

Feb 12 21:07:23 billing ppp[22883]: tun0: Phase: bundle: Terminate

Feb 12 21:07:23 billing ppp[22883]: tun0: Phase: deflink: open -> lcp

Feb 12 21:07:23 billing ppp[22883]: tun0: Phase: deflink: Disconnected!

Feb 12 21:07:23 billing ppp[22883]: tun0: Phase: deflink: lcp -> logout

Feb 12 21:07:23 billing ppp[22883]: tun0: Phase: deflink: logout -> hangup

Feb 12 21:07:23 billing ppp[22883]: tun0: Phase: deflink: Disconnected!

Feb 12 21:07:23 billing ppp[22883]: tun0: Phase: deflink: Connect time: 20 secs: 227 octets in, 244 octets out

Feb 12 21:07:23 billing ppp[22883]: tun0: Phase: deflink: 17 packets in, 17 packets out

Feb 12 21:07:23 billing ppp[22883]: tun0: Phase: total 23 bytes/sec, peak 81 bytes/sec on Sat Feb 12 21:07:11 2011

Feb 12 21:07:23 billing ppp[22883]: tun0: Phase: deflink: hangup -> opening

Feb 12 21:07:23 billing ppp[22883]: tun0: Phase: bundle: Establish

Feb 12 21:07:23 billing ppp[22883]: tun0: Phase: deflink: Enter pause (3) for redialing.

Feb 12 21:07:26 billing ppp[22883]: tun0: Phase: deflink: Connected!

Feb 12 21:07:26 billing ppp[22883]: tun0: Phase: deflink: opening -> dial

Feb 12 21:07:26 billing ppp[22883]: tun0: Phase: deflink: dial -> carrier

Feb 12 21:07:29 billing ppp[22883]: tun0: Phase: Received NGM_PPPOE_ACNAME (hook "KV-JE-R2")

Feb 12 21:07:29 billing ppp[22883]: tun0: Phase: Received NGM_PPPOE_SESSIONID

Feb 12 21:07:29 billing ppp[22883]: tun0: Phase: Received NGM_PPPOE_SUCCESS

Feb 12 21:07:29 billing ppp[22883]: tun0: Phase: deflink: carrier -> login

Feb 12 21:07:29 billing ppp[22883]: tun0: Phase: deflink: login -> lcp

Feb 12 21:07:30 billing ppp[22883]: tun0: Phase: bundle: Authenticate

Feb 12 21:07:30 billing ppp[22883]: tun0: Phase: deflink: his = PAP, mine = none

Feb 12 21:07:30 billing ppp[22883]: tun0: Phase: Pap Output: my login ********

Feb 12 21:07:30 billing ppp[22883]: tun0: Phase: Pap Input: SUCCESS ()

Feb 12 21:07:30 billing ppp[22883]: tun0: Phase: deflink: lcp -> open

Feb 12 21:07:30 billing ppp[22883]: tun0: Phase: bundle: Network

Feb 12 21:07:30 billing ppp[22883]: tun0: Phase: deflink: IPV6CP protocol reject closes IPV6CP !

Feb 12 21:07:30 billing ppp[22883]: tun0: Phase: deflink: IPV6CP protocol reject closes IPV6CP !

Feb 12 21:07:30 billing ppp[22883]: tun0: Warning: iface add: ioctl(SIOCAIFADDR, 178.94.96.112 -> 195.5.5.204): File exists

Feb 12 21:07:30 billing ppp[22883]: tun0: Error: ipcp_InterfaceUp: unable to set ip address

Feb 12 21:07:33 billing ppp[22883]: tun0: Phase: deflink: IPV6CP protocol reject closes IPV6CP !

Feb 12 21:07:42 billing last message repeated 3 times

Feb 12 21:07:45 billing ppp[22883]: tun0: Phase: bundle: Terminate

Feb 12 21:07:45 billing ppp[22883]: tun0: Phase: deflink: open -> lcp

Feb 12 21:07:45 billing ppp[22883]: tun0: Phase: deflink: Disconnected!

Feb 12 21:07:45 billing ppp[22883]: tun0: Phase: deflink: lcp -> logout

Feb 12 21:07:45 billing ppp[22883]: tun0: Phase: deflink: logout -> hangup

Feb 12 21:07:45 billing ppp[22883]: tun0: Phase: deflink: Disconnected!

Feb 12 21:07:45 billing ppp[22883]: tun0: Phase: deflink: Connect time: 19 secs: 227 octets in, 244 octets out

Feb 12 21:07:45 billing ppp[22883]: tun0: Phase: deflink: 34 packets in, 34 packets out

Feb 12 21:07:45 billing ppp[22883]: tun0: Phase: total 24 bytes/sec, peak 81 bytes/sec on Sat Feb 12 21:07:34 2011

Feb 12 21:07:45 billing ppp[22883]: tun0: Phase: deflink: hangup -> opening

Feb 12 21:07:45 billing ppp[22883]: tun0: Phase: bundle: Establish

Feb 12 21:07:45 billing ppp[22883]: tun0: Phase: deflink: Enter pause (3) for redialing.

Feb 12 21:07:48 billing ppp[22883]: tun0: Phase: deflink: Connected!

Feb 12 21:07:48 billing ppp[22883]: tun0: Phase: deflink: opening -> dial

Feb 12 21:07:48 billing ppp[22883]: tun0: Phase: deflink: dial -> carrier

Feb 12 21:07:51 billing ppp[22883]: tun0: Phase: Received NGM_PPPOE_ACNAME (hook "KV-JE-R2")

Feb 12 21:07:51 billing ppp[22883]: tun0: Phase: Received NGM_PPPOE_SESSIONID

Feb 12 21:07:51 billing ppp[22883]: tun0: Phase: Received NGM_PPPOE_SUCCESS

Feb 12 21:07:51 billing ppp[22883]: tun0: Phase: deflink: carrier -> login

Feb 12 21:07:51 billing ppp[22883]: tun0: Phase: deflink: login -> lcp

Feb 12 21:07:52 billing ppp[22883]: tun0: Phase: bundle: Authenticate

Feb 12 21:07:52 billing ppp[22883]: tun0: Phase: deflink: his = PAP, mine = none

Feb 12 21:07:52 billing ppp[22883]: tun0: Phase: Pap Output: my login ********

Feb 12 21:07:53 billing ppp[22883]: tun0: Phase: Pap Input: SUCCESS ()

Feb 12 21:07:53 billing ppp[22883]: tun0: Phase: deflink: lcp -> open

Feb 12 21:07:53 billing ppp[22883]: tun0: Phase: bundle: Network

Feb 12 21:07:53 billing ppp[22883]: tun0: Phase: deflink: IPV6CP protocol reject closes IPV6CP !

Feb 12 21:07:53 billing ppp[22883]: tun0: Phase: deflink: IPV6CP protocol reject closes IPV6CP !

Feb 12 21:07:53 billing ppp[22883]: tun0: Warning: iface add: ioctl(SIOCAIFADDR, 178.94.47.118 -> 195.5.5.204): File exists

Feb 12 21:07:53 billing ppp[22883]: tun0: Error: ipcp_InterfaceUp: unable to set ip address

Feb 12 21:07:56 billing ppp[22883]: tun0: Phase: deflink: IPV6CP protocol reject closes IPV6CP !

Feb 12 21:08:05 billing last message repeated 3 times

Feb 12 21:08:08 billing ppp[22883]: tun0: Phase: bundle: Terminate

Feb 12 21:08:08 billing ppp[22883]: tun0: Phase: deflink: open -> lcp

Feb 12 21:08:08 billing ppp[22883]: tun0: Phase: deflink: Disconnected!

Feb 12 21:08:08 billing ppp[22883]: tun0: Phase: deflink: lcp -> logout

Feb 12 21:08:08 billing ppp[22883]: tun0: Phase: deflink: logout -> hangup

Feb 12 21:08:08 billing ppp[22883]: tun0: Phase: deflink: Disconnected!

Feb 12 21:08:08 billing ppp[22883]: tun0: Phase: deflink: Connect time: 20 secs: 227 octets in, 244 octets out

Feb 12 21:08:08 billing ppp[22883]: tun0: Phase: deflink: 51 packets in, 51 packets out

Feb 12 21:08:08 billing ppp[22883]: tun0: Phase: total 23 bytes/sec, peak 81 bytes/sec on Sat Feb 12 21:07:56 2011

Feb 12 21:08:08 billing ppp[22883]: tun0: Phase: deflink: hangup -> opening

Feb 12 21:08:08 billing ppp[22883]: tun0: Phase: bundle: Establish

Feb 12 21:08:08 billing ppp[22883]: tun0: Phase: deflink: Enter pause (3) for redialing.

Link to post
Share on other sites
roneaf

roneaf 2

Posted
Posted

Я только начинающий пользователь *nix н у меня на FreeBSD 8.0 работает такой конфиг

inet:
set device PPPoE:em0:1
set authname 1
set authkey 1
set dial
set login
set openmode active
set mppe 128 stateful
set timeout 180
set redial 0 0
disable ipv6cp
disable ipv6
disable pred1
deny pred1
disable lqr
deny lqr
add default HISADDR

Link to post
Share on other sites
natiss

natiss 16

Posted
Posted

http://myfreebsd.ru/network/pppoe-klient-user-levelpppoe:

 

set log Phase Chat LCP IPCP CCP tun command
ident user-ppp VERSION (built COMPILATIONDATE)
set device PPPoE:fxp0  # указываем интерфейс (физический или vlan) к которому подключен провайдер
set speed sync
set mru 1492
set mtu 1492
set ctsrts off
enable lqr
add default HISADDR  #  добавляем маршрут по умолчанию
set dns 8.8.8.8  # устанавливаем DNS (можно указывать Google)
set authname  username # логин
set authkey  passwd  # пароль
[b]set dial
set login[/b]

Link to post
Share on other sites
natiss

natiss 16

Posted
Posted

Ну или так

 

/usr/local/sbin/mpd5 -d /usr/local/etc/mpd5-ut -p /var/run/mpd5-ut.pid -b

 

 

# cat /usr/local/etc/mpd5-ut/mpd.conf | less
startup:
       # configure mpd users
       set user foo bar admin
       set user foo1 bar1
       # configure the console
       set console self 127.0.0.1 5007
       set console open


default:
       load ut


ut:
#
# PPPoE client: only outgoing calls, auto reconnect,
# ipcp-negotiated address, one-sided authentication,
# default route points on ISP's end
#

       create bundle static B1
      set iface route default
       set ipcp ranges 0.0.0.0/0 0.0.0.0/0

       create link static L1 pppoe
       set link action bundle B1
       set auth authname bdsmbsdm999@dsl.ukrtel.net
       set auth password harDcOre
       set link max-redial 0
       set link mtu 1460
       set link keep-alive 10 60
       set pppoe iface ed0
       set pppoe service ""
       open

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Followers 0
Go to topic listing

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...