pa4ka_ 0 Опубликовано: 2012-12-14 14:09:11 Share Опубликовано: 2012-12-14 14:09:11 Уже 4 день подряд перегружаеться сервер маршрутизации Понимаю что изза dummynet, но что именно незнаю. На сервере ничего не менялось. Помогите пожалуйста разобраться. uname -a FreeBSD tr_bnet 7.3-RELEASE FreeBSD 7.3-RELEASE #0: Thu Jun 28 12:34:35 UTC 2012 pa4ka@tr_bnet:/usr/src/sys/i386/compile/BNETRAYON i386 /var/crach/vmcore0 Fatal trap 12: page fault while in kernel mode cpuid = 0; apic id = 00 fault virtual address = 0xc fault code = supervisor read, page not present instruction pointer = 0x20:0xc089e628 stack pointer = 0x28:0xc6ed7b54 frame pointer = 0x28:0xc6ed7b70 code segment = base 0x0, limit 0xfffff, type 0x1b = DPL 0, pres 1, def32 1, gran 1 processor eflags = interrupt enabled, resume, IOPL = 0 current process = 55 (dummynet) trap number = 12 panic: page fault cpuid = 0 Uptime: 6d5h45m42s Physical memory: 3571 MB Ядро # # GENERIC -- Generic kernel configuration file for FreeBSD/i386 # # For more information on this file, please read the handbook section on # Kernel Configuration Files: # # http://www.FreeBSD.org/doc/en_US.ISO8859-1/books/handbook/kernelconfig-config.html # # The handbook is also available locally in /usr/share/doc/handbook # if you've installed the doc distribution, otherwise always see the # FreeBSD World Wide Web server (http://www.FreeBSD.org/) for the # latest information. # # An exhaustive list of options and more detailed explanations of the # device lines is also present in the ../../conf/NOTES and NOTES files. # If you are in doubt as to the purpose or necessity of a line, check first # in NOTES. # # $FreeBSD: src/sys/i386/conf/GENERIC,v 1.474.2.22.2.1 2010/02/10 00:26:20 kensmith Exp $ #cpu I486_CPU #cpu I586_CPU cpu I686_CPU ident GENERIC # To statically compile in device wiring instead of /boot/device.hints #hints "GENERIC.hints" # Default places to look for devices. makeoptions DEBUG=-g # Build kernel with gdb(1) debug symbols options SCHED_ULE # ULE scheduler options PREEMPTION # Enable kernel thread preemption options INET # InterNETworking options INET6 # IPv6 communications protocols options SCTP # Stream Control Transmission Protocol options FFS # Berkeley Fast Filesystem options SOFTUPDATES # Enable FFS soft updates support options UFS_ACL # Support for access control lists options UFS_DIRHASH # Improve performance on big directories options UFS_GJOURNAL # Enable gjournal-based UFS journaling options MD_ROOT # MD is a potential root device options NFSCLIENT # Network Filesystem Client options NFSSERVER # Network Filesystem Server options NFSLOCKD # Network Lock Manager options NFS_ROOT # NFS usable as /, requires NFSCLIENT options MSDOSFS # MSDOS Filesystem options CD9660 # ISO 9660 Filesystem options PROCFS # Process filesystem (requires PSEUDOFS) options PSEUDOFS # Pseudo-filesystem framework options GEOM_PART_GPT # GUID Partition Tables. options GEOM_LABEL # Provides labelization options COMPAT_43TTY # BSD 4.3 TTY compat [KEEP THIS!] options COMPAT_FREEBSD4 # Compatible with FreeBSD4 options COMPAT_FREEBSD5 # Compatible with FreeBSD5 options COMPAT_FREEBSD6 # Compatible with FreeBSD6 options SCSI_DELAY=5000 # Delay (in ms) before probing SCSI options KTRACE # ktrace(1) support options STACK # stack(9) support options SYSVSHM # SYSV-style shared memory options SYSVMSG # SYSV-style message queues options SYSVSEM # SYSV-style semaphores options P1003_1B_SEMAPHORES # POSIX-style semaphores options _KPOSIX_PRIORITY_SCHEDULING # POSIX P1003_1B real-time extensions options KBD_INSTALL_CDEV # install a CDEV entry in /dev options ADAPTIVE_GIANT # Giant mutex is adaptive. options STOP_NMI # Stop CPUS using NMI instead of IPI options AUDIT # Security event auditing #options KDTRACE_HOOKS # Kernel DTrace hooks options INCLUDE_CONFIG_FILE # Include this file in kernel # To make an SMP kernel, the next two lines are needed options SMP # Symmetric MultiProcessor Kernel device apic # I/O APIC # CPU frequency control device cpufreq # Bus support. device eisa device pci # Floppy drives device fdc # ATA and ATAPI devices device ata device atadisk # ATA disk drives device ataraid # ATA RAID drives device atapicd # ATAPI CDROM drives device atapifd # ATAPI floppy drives device atapist # ATAPI tape drives options ATA_STATIC_ID # Static device numbering # SCSI Controllers device ahb # EISA AHA1742 family device ahc # AHA2940 and onboard AIC7xxx devices options AHC_REG_PRETTY_PRINT # Print register bitfields in debug # output. Adds ~128k to driver. device ahd # AHA39320/29320 and onboard AIC79xx devices options AHD_REG_PRETTY_PRINT # Print register bitfields in debug # output. Adds ~215k to driver. device amd # AMD 53C974 (Tekram DC-390(T)) device hptiop # Highpoint RocketRaid 3xxx series device isp # Qlogic family #device ispfw # Firmware for QLogic HBAs- normally a module device mpt # LSI-Logic MPT-Fusion #device ncr # NCR/Symbios Logic device sym # NCR/Symbios Logic (newer chipsets + those of `ncr') device trm # Tekram DC395U/UW/F DC315U adapters device adv # Advansys SCSI adapters device adw # Advansys wide SCSI adapters device aha # Adaptec 154x SCSI adapters device aic # Adaptec 15[012]x SCSI adapters, AIC-6[23]60. device bt # Buslogic/Mylex MultiMaster SCSI adapters device ncv # NCR 53C500 device nsp # Workbit Ninja SCSI-3 device stg # TMC 18C30/18C50 # SCSI peripherals device scbus # SCSI bus (required for SCSI) device ch # SCSI media changers device da # Direct Access (disks) device sa # Sequential Access (tape etc) device cd # CD device pass # Passthrough device (direct SCSI access) device ses # SCSI Environmental Services (and SAF-TE) # RAID controllers interfaced to the SCSI subsystem device amr # AMI MegaRAID device arcmsr # Areca SATA II RAID device asr # DPT SmartRAID V, VI and Adaptec SCSI RAID device ciss # Compaq Smart RAID 5* device dpt # DPT Smartcache III, IV - See NOTES for options device hptmv # Highpoint RocketRAID 182x device hptrr # Highpoint RocketRAID 17xx, 22xx, 23xx, 25xx device iir # Intel Integrated RAID device ips # IBM (Adaptec) ServeRAID device mly # Mylex AcceleRAID/eXtremeRAID device twa # 3ware 9000 series PATA/SATA RAID # RAID controllers device aac # Adaptec FSA RAID device aacp # SCSI passthrough for aac (requires CAM) device ida # Compaq Smart RAID device mfi # LSI MegaRAID SAS device mlx # Mylex DAC960 family device pst # Promise Supertrak SX6000 device twe # 3ware ATA RAID # atkbdc0 controls both the keyboard and the PS/2 mouse device atkbdc # AT keyboard controller device atkbd # AT keyboard device psm # PS/2 mouse device kbdmux # keyboard multiplexer device vga # VGA video card driver device splash # Splash screen and screen saver support # syscons is the default console driver, resembling an SCO console device sc device agp # support several AGP chipsets # Power management support (see NOTES for more options) #device apm # Add suspend/resume support for the i8254. device pmtimer # PCCARD (PCMCIA) support # PCMCIA and cardbus bridge support device cbb # cardbus (yenta) bridge device pccard # PC Card (16-bit) bus device cardbus # CardBus (32-bit) bus # Serial (COM) ports device sio # 8250, 16[45]50 based serial ports device uart # Generic UART driver # Parallel port device ppc device ppbus # Parallel port bus (required) device lpt # Printer device plip # TCP/IP over parallel device ppi # Parallel port interface device #device vpo # Requires scbus and da # If you've got a "dumb" serial or parallel PCI card that is # supported by the puc(4) glue driver, uncomment the following # line to enable it (connects to sio, uart and/or ppc drivers): #device puc # PCI Ethernet NICs. device de # DEC/Intel DC21x4x (``Tulip'') device em # Intel PRO/1000 Gigabit Ethernet Family device igb # Intel PRO/1000 PCIE Server Gigabit Family device ixgb # Intel PRO/10GbE Ethernet Card device le # AMD Am7900 LANCE and Am79C9xx PCnet device txp # 3Com 3cR990 (``Typhoon'') device vx # 3Com 3c590, 3c595 (``Vortex'') # PCI Ethernet NICs that use the common MII bus controller code. # NOTE: Be sure to keep the 'device miibus' line in order to use these NICs! device miibus # MII bus support device age # Attansic/Atheros L1 Gigabit Ethernet device alc # Atheros AR8131/AR8132 Ethernet device ale # Atheros AR8121/AR8113/AR8114 Ethernet device bce # Broadcom BCM5706/BCM5708 Gigabit Ethernet device bfe # Broadcom BCM440x 10/100 Ethernet device bge # Broadcom BCM570xx Gigabit Ethernet device dc # DEC/Intel 21143 and various workalikes device et # Agere ET1310 10/100/Gigabit Ethernet device fxp # Intel EtherExpress PRO/100B (82557, 82558) device jme # JMicron JMC250 Gigabit/JMC260 Fast Ethernet device lge # Level 1 LXT1001 gigabit Ethernet device msk # Marvell/SysKonnect Yukon II Gigabit Ethernet device nfe # nVidia nForce MCP on-board Ethernet device nge # NatSemi DP83820 gigabit Ethernet #device nve # nVidia nForce MCP on-board Ethernet Networking device pcn # AMD Am79C97x PCI 10/100 (precedence over 'le') device re # RealTek 8139C+/8169/8169S/8110S device rl # RealTek 8129/8139 device sf # Adaptec AIC-6915 (``Starfire'') device sis # Silicon Integrated Systems SiS 900/SiS 7016 device sk # SysKonnect SK-984x & SK-982x gigabit Ethernet device ste # Sundance ST201 (D-Link DFE-550TX) device stge # Sundance/Tamarack TC9021 gigabit Ethernet device ti # Alteon Networks Tigon I/II gigabit Ethernet device tl # Texas Instruments ThunderLAN device tx # SMC EtherPower II (83c170 ``EPIC'') device vge # VIA VT612x gigabit Ethernet device vr # VIA Rhine, Rhine II device wb # Winbond W89C840F device xl # 3Com 3c90x (``Boomerang'', ``Cyclone'') # ISA Ethernet NICs. pccard NICs included. device cs # Crystal Semiconductor CS89x0 NIC # 'device ed' requires 'device miibus' device ed # NE[12]000, SMC Ultra, 3c503, DS8390 cards device ex # Intel EtherExpress Pro/10 and Pro/10+ device ep # Etherlink III based cards device fe # Fujitsu MB8696x based cards device ie # EtherExpress 8/16, 3C507, StarLAN 10 etc. device sn # SMC's 9000 series of Ethernet chips device xe # Xircom pccard Ethernet # Wireless NIC cards device wlan # 802.11 support device wlan_wep # 802.11 WEP support device wlan_ccmp # 802.11 CCMP support device wlan_tkip # 802.11 TKIP support device wlan_amrr # AMRR transmit rate control algorithm device wlan_scan_ap # 802.11 AP mode scanning device wlan_scan_sta # 802.11 STA mode scanning device an # Aironet 4500/4800 802.11 wireless NICs. device ath # Atheros pci/cardbus NIC's device ath_hal # Atheros HAL (Hardware Access Layer) options AH_SUPPORT_AR5416 # enable AR5416 tx/rx descriptors device ath_rate_sample # SampleRate tx rate control for ath device awi # BayStack 660 and others device ral # Ralink Technology RT2500 wireless NICs. device wi # WaveLAN/Intersil/Symbol 802.11 wireless NICs. #device wl # Older non 802.11 Wavelan wireless NIC. # Pseudo devices. device loop # Network loopback device random # Entropy device device ether # Ethernet support device vlan # 802.1Q VLAN support device sl # Kernel SLIP device ppp # Kernel PPP device tun # Packet tunnel. device pty # Pseudo-ttys (telnet etc) device md # Memory "disks" device gif # IPv6 and IPv4 tunneling device faith # IPv6-to-IPv4 relaying (translation) device firmware # firmware assist module # The `bpf' device enables the Berkeley Packet Filter. # Be aware of the administrative consequences of enabling this! # Note that 'bpf' is required for DHCP. device bpf # Berkeley packet filter # USB support device uhci # UHCI PCI->USB interface device ohci # OHCI PCI->USB interface device ehci # EHCI PCI->USB interface (USB 2.0) device usb # USB Bus (required) #device udbp # USB Double Bulk Pipe devices device ugen # Generic device uhid # "Human Interface Devices" device ukbd # Keyboard device ulpt # Printer device umass # Disks/Mass storage - Requires scbus and da device ums # Mouse device urio # Diamond Rio 500 MP3 player device uscanner # Scanners # USB Serial devices device ucom # Generic com ttys device uark # Technologies ARK3116 based serial adapters device ubsa # Belkin F5U103 and compatible serial adapters device ubser # BWCT console serial adapters device uftdi # For FTDI usb serial adapters device uipaq # Some WinCE based devices device uplcom # Prolific PL-2303 serial adapters device uslcom # SI Labs CP2101/CP2102 serial adapters device uvisor # Visor and Palm devices device uvscom # USB serial support for DDI pocket's PHS # USB Ethernet, requires miibus device aue # ADMtek USB Ethernet device axe # ASIX Electronics USB Ethernet device cdce # Generic USB over Ethernet device cue # CATC USB Ethernet device kue # Kawasaki LSI USB Ethernet device rue # RealTek RTL8150 USB Ethernet # USB Wireless device rum # Ralink Technology RT2501USB wireless NICs device ural # Ralink Technology RT2500USB wireless NICs # FireWire support device firewire # FireWire bus code device sbp # SCSI over FireWire (Requires scbus and da) device fwe # Ethernet over FireWire (non-standard!) device fwip # IP over FireWire (RFC 2734,3146) device dcons # Dumb console driver device dcons_crom # Configuration ROM for dcons options HZ=1000 options IPFIREWALL options IPFIREWALL_FORWARD options IPDIVERT options DUMMYNET #options IPFIREWALL_NAT #options LIBALIAS options ROUTETABLES=4 options SCHED_ULE device pf device pflog device pfsync options ALTQ options ALTQ_CBQ # Class Bases Queuing (CBQ) options ALTQ_RED # Random Early Detection (RED) options ALTQ_RIO # RED In/Out options ALTQ_HFSC # Hierarchical Packet Scheduler (HFSC) options ALTQ_PRIQ # Priority Queuing (PRIQ) options ALTQ_NOPCC # Required for SMP build options GEOM_MIRROR # Disk mirroring. options GEOM_JOURNAL # Journaling. # netgraph(4). Enable the base netgraph code with the NETGRAPH option. options NETGRAPH # netgraph(4) system options NETGRAPH_BPF #options NETGRAPH_BRIDGE #options NETGRAPH_CAR options NETGRAPH_ETHER options NETGRAPH_IFACE options NETGRAPH_IPFW options NETGRAPH_KSOCKET #options NETGRAPH_MPPC_COMPRESSION #options NETGRAPH_MPPC_ENCRYPTION #options NETGRAPH_NETFLOW #options NETGRAPH_NAT options NETGRAPH_ONE2MANY options NETGRAPH_PPP options NETGRAPH_PPPOE options NETGRAPH_PPTPGRE options NETGRAPH_SOCKET options NETGRAPH_SPLIT options NETGRAPH_TCPMSS options NETGRAPH_TEE options NETGRAPH_VJC Ссылка на сообщение Поделиться на других сайтах
sergeev 1 Опубліковано: 2012-12-14 14:21:02 Share Опубліковано: 2012-12-14 14:21:02 А подробней можно? top -SIHP(в момент падения если успеете) , ipfw list Ссылка на сообщение Поделиться на других сайтах
pa4ka_ 0 Опубліковано: 2012-12-14 14:23:31 Автор Share Опубліковано: 2012-12-14 14:23:31 Напишу все подробности какие надо. top-SHIP думаю не успею потому что два раза в день не синхронно делает) 00050 allow tcp from any to me dst-port 22 00051 allow tcp from me 22 to any 00110 allow ip from any to any via lo0 00120 skipto 1000 ip from me to any 00130 deny icmp from any to any in icmptypes 5,9,13,14,15,16,17 00160 skipto 2000 ip from any to me 00200 skipto 700 ip from any to any via bge0 00280 fwd 127.0.0.1,8081 tcp from table(35) to not me dst-port 80 in 00290 fwd 127.0.0.1,8082 tcp from not table(0) to not me dst-port 80 in 00350 skipto 4500 ip from any to any in 00400 skipto 450 ip from any to any recv bge0 00520 tee 1 ip from any to any 00550 tee 2 ip from any to any 00590 allow ip from any to any 00700 skipto 32500 ip from any to any in 00710 tee 1 ip from any to any 00740 allow ip from any to any 01000 allow udp from any 53,7723 to any 01010 allow tcp from any to any setup keep-state 01020 allow udp from any to any keep-state 01100 allow ip from any to any 02000 check-state 02010 allow icmp from any to any 02020 allow tcp from any to any dst-port 80,443 02050 deny ip from any to any via bge0 02100 allow udp from any to any dst-port 53,7723 02110 allow tcp from any to any dst-port 1194 02200 deny ip from any to any 05000 deny ip from not table(0) to any 05001 skipto 5010 ip from table(127) to table(126) 05002 skipto 5030 ip from any to not table(2) 05003 deny ip from any to not table(1) 05004 pipe tablearg ip from table(21) to any 05005 deny ip from any to any 05010 pipe tablearg ip from table(127) to any 05030 deny tcp from table(15) to any dst-port 25 05400 pipe tablearg ip from table(11) to any 32000 deny ip from any to any 32490 deny ip from any to any 33000 pipe tablearg ip from table(126) to table(127) 33001 skipto 33010 ip from not table(2) to any 33002 pipe tablearg ip from any to table(20) 33003 deny ip from any to any 33400 pipe tablearg ip from any to table(10) 65535 deny ip from any to any Ссылка на сообщение Поделиться на других сайтах
rootvm 1 Опубліковано: 2012-12-14 14:26:24 Share Опубліковано: 2012-12-14 14:26:24 http://www.opennet.ru/base/sys/freebsd_panic_solution.txt.html Не ваша ситуация? Ссылка на сообщение Поделиться на других сайтах
pa4ka_ 0 Опубліковано: 2012-12-14 14:36:42 Автор Share Опубліковано: 2012-12-14 14:36:42 http://www.opennet.r...lution.txt.html Не ваша ситуация? перед падением в messages только ето Dec 14 14:01:28 tr_bnet kernel: Fatal trap 12: page fault while in kernel mode Dec 14 14:01:28 tr_bnet kernel: cpuid = 1; apic id = 01 Dec 14 14:01:28 tr_bnet kernel: fault virtual address<->= 0xc Dec 14 14:01:28 tr_bnet kernel: fault code<----><------>= supervisor read, page not present Dec 14 14:01:28 tr_bnet kernel: instruction pointer<--->= 0x20:0xc089f816 Dec 14 14:01:28 tr_bnet kernel: stack pointer<-> = 0x28:0xc6ed7a84 Dec 14 14:01:28 tr_bnet kernel: frame pointer<-> = 0x28:0xc6ed7ab0 Dec 14 14:01:28 tr_bnet kernel:. Dec 14 14:01:28 tr_bnet kernel: code segment<--><------>= base. Dec 14 14:01:28 tr_bnet kernel: 0x0, limi Dec 14 14:01:28 tr_bnet kernel: t 0xffff Dec 14 14:01:28 tr_bnet kernel: f, type 0 Dec 14 14:01:28 tr_bnet kernel: x1b Dec 14 14:01:28 tr_bnet kernel:. Dec 14 14:01:28 tr_bnet kernel: = DPL 0,. Dec 14 14:01:28 tr_bnet kernel: pres 1,. Dec 14 14:01:28 tr_bnet kernel: def32 1, Dec 14 14:01:28 tr_bnet kernel: gran 1 Dec 14 14:01:28 tr_bnet kernel: processor eflag Dec 14 14:01:28 tr_bnet kernel: s<----->= inte Dec 14 14:01:28 tr_bnet kernel: rrupt e Dec 14 14:01:28 tr_bnet kernel: nabled,. Dec 14 14:01:28 tr_bnet kernel: resume,. Dec 14 14:01:28 tr_bnet kernel: IOPL = 0 Ссылка на сообщение Поделиться на других сайтах
sergeev 1 Опубліковано: 2012-12-14 14:47:00 Share Опубліковано: 2012-12-14 14:47:00 Да это еще шикарно 2 раза в день, у нас 1 раз в два-пять дней NASы ребутились, ставил ping localhost, и постоянно наблюдал и как только начинались дропы снимал статистику, пробывал тут же на лету увеличивать буферы и т.д. ни чего не помогало и через пару-тройку минут NAS уходил в ребут. Freebsd 9, пробывал откатываться на 8. MPD5.6, pptp, ipfw nat, ospf, карты broadcom. Ребуты происходили не зависимо от нагрузки, кол-ва тунелей и времени суток. Причем если в момент падения сервера выключить нат, то его работа сразу же стабилизировалась. В итоге перешли на pf. Ссылка на сообщение Поделиться на других сайтах
pa4ka_ 0 Опубліковано: 2012-12-14 14:50:34 Автор Share Опубліковано: 2012-12-14 14:50:34 Сервер маршрутизации с биллингом NoDeny. Устанавливалось с коробки Может проблема с винтами? Стоит RAID 5. Можно ли их проверить удалённо? Ссылка на сообщение Поделиться на других сайтах
adeep 212 Опубліковано: 2012-12-14 14:59:03 Share Опубліковано: 2012-12-14 14:59:03 tso rxsum txsum на сетевушках выключите. Ссылка на сообщение Поделиться на других сайтах
sergeev 1 Опубліковано: 2012-12-14 15:05:16 Share Опубліковано: 2012-12-14 15:05:16 Попробуйте перейти на pf, у вас ядро собрано с его поддержкой, делов две минуты пользователи даже ничего не заметят. Ссылка на сообщение Поделиться на других сайтах
pa4ka_ 0 Опубліковано: 2012-12-14 15:11:47 Автор Share Опубліковано: 2012-12-14 15:11:47 Попробуйте перейти на pf, у вас ядро собрано с его поддержкой, делов две минуты пользователи даже ничего не заметят. ну с коробки по доке всё на pf, кроме того что он в ядре set limit states 128000 set optimization aggressive nat pass on bge0 from 172.21.0.0/16 to any -> bge0 Ссылка на сообщение Поделиться на других сайтах
sergeev 1 Опубліковано: 2012-12-14 15:31:29 Share Опубліковано: 2012-12-14 15:31:29 Попробуйте обновится до 9 версии, вырубите я ядре inet6, отключите проверку контрольных сумм на интерфейсе, dummynet заменить на ng_car если биллинг позволяет. MPD какой у Вас? Ссылка на сообщение Поделиться на других сайтах
pa4ka_ 0 Опубліковано: 2012-12-14 15:37:09 Автор Share Опубліковано: 2012-12-14 15:37:09 Попробуйте обновится до 9 версии, вырубите я ядре inet6, отключите проверку контрольных сумм на интерфейсе, dummynet заменить на ng_car если биллинг позволяет. MPD какой у Вас? mpd нету, привязка по IP+MAC выдаеться DHCP сервером клиентам Ссылка на сообщение Поделиться на других сайтах
pa4ka_ 0 Опубліковано: 2012-12-14 16:29:27 Автор Share Опубліковано: 2012-12-14 16:29:27 Отключил проверку контрольных сумм и через две минуты лёг( Ссылка на сообщение Поделиться на других сайтах
Artcv 4 Опубліковано: 2012-12-14 16:42:22 Share Опубліковано: 2012-12-14 16:42:22 была такая ситуация! тоже биллинг ноудени Решил: Ядро 64 бит С ядра все лишнее убрано! + сетевую поставил em0 Ссылка на сообщение Поделиться на других сайтах
pa4ka_ 0 Опубліковано: 2012-12-14 16:58:51 Автор Share Опубліковано: 2012-12-14 16:58:51 была такая ситуация! тоже биллинг ноудени Решил: Ядро 64 бит С ядра все лишнее убрано! + сетевую поставил em0 А просто сетевую поставить не помогло? Ссылка на сообщение Поделиться на других сайтах
Ajar 92 Опубліковано: 2012-12-14 18:36:15 Share Опубліковано: 2012-12-14 18:36:15 Может чегото перегревается ? Поставьте пакет sensor помониторьте ... Ссылка на сообщение Поделиться на других сайтах
KaYot 3 707 Опубліковано: 2012-12-14 18:44:22 Share Опубліковано: 2012-12-14 18:44:22 Или память/винт битые. Начинать надо с простого. Ссылка на сообщение Поделиться на других сайтах
Artcv 4 Опубліковано: 2012-12-14 19:51:58 Share Опубліковано: 2012-12-14 19:51:58 была такая ситуация! тоже биллинг ноудени Решил: Ядро 64 бит С ядра все лишнее убрано! + сетевую поставил em0 А просто сетевую поставить не помогло? Не экспериментировал когда сервер начал пару раз в день перегружаться - сразу на тестовом компе настроил заново систему с теми параметрами что выше написал, переставил винты и работаем дальше! Ссылка на сообщение Поделиться на других сайтах
tivi 56 Опубліковано: 2012-12-14 20:03:46 Share Опубліковано: 2012-12-14 20:03:46 Или память/винт битые. Начинать надо с простого. +1 за память. Ссылка на сообщение Поделиться на других сайтах
Ajar 92 Опубліковано: 2012-12-14 21:32:03 Share Опубліковано: 2012-12-14 21:32:03 Или память/винт битые. Начинать надо с простого. Не шарю во фре , но в дистрах линекса отличный memtest, для веников smartctl Ссылка на сообщение Поделиться на других сайтах
ucTuHa 199 Опубліковано: 2013-01-03 10:49:50 Share Опубліковано: 2013-01-03 10:49:50 Дабы не стартовать новую тему: Сегодня отпала на роутере сетевая которая смотрит в сторону биллинга, может кто подскажет в чем беда, в логах такое: Jan 3 12:02:45 bras1 syslogd: kernel boot file is /boot/kernel/kernel Jan 3 12:02:45 bras1 kernel: Copyright © 1992-2011 The FreeBSD Project. Jan 3 12:02:45 bras1 kernel: Copyright © 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 Jan 3 12:02:45 bras1 kernel: The Regents of the University of California. All rights reserved. Jan 3 12:02:45 bras1 kernel: FreeBSD is a registered trademark of The FreeBSD Foundation. Jan 3 12:02:45 bras1 kernel: FreeBSD 8.2-STABLE #0 r226362: Fri Oct 14 21:53:34 EEST 2011 Jan 3 12:02:45 bras1 kernel: smail@bras1.galaxy:/usr/obj/usr/src/sys/BRAS111014 amd64 Jan 3 12:02:45 bras1 kernel: Timecounter "i8254" frequency 1193182 Hz quality 0 Jan 3 12:02:45 bras1 kernel: CPU: Intel® Core i3 CPU 550 @ 3.20GHz (3211.20-MHz K8-class CPU) Jan 3 12:02:45 bras1 kernel: Origin = "GenuineIntel" Id = 0x20655 Family = 6 Model = 25 Stepping = 5 Jan 3 12:02:45 bras1 kernel: Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2, Jan 3 12:02:45 bras1 kernel: Features2=0x9ae3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,POPCNT> Jan 3 12:02:45 bras1 kernel: AMD Features=0x28100800<SYSCALL,NX,RDTSCP,LM> Jan 3 12:02:45 bras1 kernel: AMD Features2=0x1<LAHF> Jan 3 12:02:45 bras1 kernel: TSC: P-state invariant Jan 3 12:02:45 bras1 kernel: real memory = 2147483648 (2048 MB) Jan 3 12:02:45 bras1 kernel: avail memory = 2046537728 (1951 MB) Jan 3 12:02:45 bras1 kernel: ACPI APIC Table: <070810 APIC1518> Jan 3 12:02:45 bras1 kernel: FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs Jan 3 12:02:45 bras1 kernel: FreeBSD/SMP: 1 package(s) x 2 core(s) x 2 SMT threads Jan 3 12:02:45 bras1 kernel: cpu0 (BSP): APIC ID: 0 Jan 3 12:02:45 bras1 kernel: cpu1 (AP): APIC ID: 1 Jan 3 12:02:45 bras1 kernel: cpu2 (AP): APIC ID: 4 Jan 3 12:02:45 bras1 kernel: cpu3 (AP): APIC ID: 5 Jan 3 12:02:45 bras1 kernel: ioapic0: Changing APIC ID to 6 Jan 3 12:02:45 bras1 kernel: ioapic0 <Version 2.0> irqs 0-23 on motherboard Jan 3 12:02:45 bras1 kernel: kbd1 at kbdmux0 Jan 3 12:02:45 bras1 kernel: acpi0: <070810 XSDT1518> on motherboard Jan 3 12:02:45 bras1 kernel: acpi0: [iTHREAD] Jan 3 12:02:45 bras1 kernel: acpi0: Power Button (fixed) Jan 3 12:02:45 bras1 kernel: acpi0: reservation of fee00000, 1000 (3) failed Jan 3 12:02:45 bras1 kernel: acpi0: reservation of 0, a0000 (3) failed Jan 3 12:02:45 bras1 kernel: acpi0: reservation of 100000, 7ff00000 (3) failed Jan 3 12:02:45 bras1 kernel: Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000 Jan 3 12:02:45 bras1 kernel: acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0 Jan 3 12:02:45 bras1 kernel: cpu0: <ACPI CPU> on acpi0 Jan 3 12:02:45 bras1 kernel: ACPI Warning: Incorrect checksum in table [OEMB] - 0x2E, should be 0x2D (20101013/tbutils-354) Jan 3 12:02:45 bras1 kernel: cpu1: <ACPI CPU> on acpi0 Jan 3 12:02:45 bras1 kernel: cpu2: <ACPI CPU> on acpi0 Jan 3 12:02:45 bras1 kernel: cpu3: <ACPI CPU> on acpi0 Jan 3 12:02:45 bras1 kernel: pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0 Jan 3 12:02:45 bras1 kernel: pci0: <ACPI PCI bus> on pcib0 Jan 3 12:02:45 bras1 kernel: pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0 Jan 3 12:02:45 bras1 kernel: pci1: <ACPI PCI bus> on pcib1 Jan 3 12:02:45 bras1 kernel: vgapci0: <VGA-compatible display> mem 0xf6000000-0xf6ffffff,0xe0000000-0xefffffff,0xf5000000-0xf5ffffff irq 16 at device 0.0 on Jan 3 12:02:45 bras1 kernel: ehci0: <Intel PCH USB 2.0 controller USB-B> mem 0xf4ffe000-0xf4ffe3ff irq 16 at device 26.0 on pci0 Jan 3 12:02:45 bras1 kernel: ehci0: [iTHREAD] Jan 3 12:02:45 bras1 kernel: usbus0: EHCI version 1.0 Jan 3 12:02:45 bras1 kernel: usbus0: <Intel PCH USB 2.0 controller USB-B> on ehci0 Jan 3 12:02:45 bras1 kernel: pci0: <multimedia, HDA> at device 27.0 (no driver attached) Jan 3 12:02:45 bras1 kernel: pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.0 on pci0 Jan 3 12:02:45 bras1 kernel: pci6: <ACPI PCI bus> on pcib2 Jan 3 12:02:45 bras1 kernel: pcib3: <ACPI PCI-PCI bridge> irq 17 at device 28.4 on pci0 Jan 3 12:02:45 bras1 kernel: pci5: <ACPI PCI bus> on pcib3 Jan 3 12:02:45 bras1 kernel: pcib4: <ACPI PCI-PCI bridge> irq 16 at device 28.5 on pci0 Jan 3 12:02:45 bras1 kernel: pci4: <ACPI PCI bus> on pcib4 Jan 3 12:02:45 bras1 kernel: pcib5: <ACPI PCI-PCI bridge> irq 18 at device 28.6 on pci0 Jan 3 12:02:45 bras1 kernel: pci3: <ACPI PCI bus> on pcib5 Jan 3 12:02:45 bras1 kernel: atapci0: <VIA ATA controller> port 0xdc00-0xdc07,0xd880-0xd883,0xd800-0xd807,0xd480-0xd483,0xd400-0xd40f irq 18 at device 0.0 o Jan 3 12:02:45 bras1 kernel: atapci0: [iTHREAD] Jan 3 12:02:45 bras1 kernel: ata2: <ATA channel 0> on atapci0 Jan 3 12:02:45 bras1 kernel: ata2: [iTHREAD] Jan 3 12:02:45 bras1 kernel: ata3: <ATA channel 1> on atapci0 Jan 3 12:02:45 bras1 kernel: ata3: [iTHREAD] Jan 3 12:02:45 bras1 kernel: pcib6: <ACPI PCI-PCI bridge> irq 19 at device 28.7 on pci0 Jan 3 12:02:45 bras1 kernel: pci2: <ACPI PCI bus> on pcib6 Jan 3 12:02:45 bras1 kernel: re0: <RealTek 8168/8111 B/C/CP/D/DP/E PCIe Gigabit Ethernet> port 0xc800-0xc8ff mem 0xf3fff000-0xf3ffffff,0xf3ff8000-0xf3ffbfff Jan 3 12:02:45 bras1 kernel: re0: Using 1 MSI-X message Jan 3 12:02:45 bras1 kernel: re0: Chip rev. 0x28000000 Jan 3 12:02:45 bras1 kernel: re0: MAC rev. 0x00000000 Jan 3 12:02:45 bras1 kernel: miibus0: <MII bus> on re0 Jan 3 12:02:45 bras1 kernel: rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus0 Jan 3 12:02:45 bras1 kernel: rgephy0: none, 10baseT, 10baseT-FDX, 10baseT-FDX-flow, 100baseTX, 100baseTX-FDX, 100baseTX-FDX-flow, 1000baseT, 1000baseT-mast Jan 3 12:02:45 bras1 kernel: re0: Ethernet address: 20:cf:30:cd:43:c6 Jan 3 12:02:45 bras1 kernel: re0: [iTHREAD] Jan 3 12:02:45 bras1 kernel: ehci1: <Intel PCH USB 2.0 controller USB-A> mem 0xf4ffd000-0xf4ffd3ff irq 23 at device 29.0 on pci0 Jan 3 12:02:45 bras1 kernel: ehci1: [iTHREAD] Jan 3 12:02:45 bras1 kernel: usbus1: EHCI version 1.0 Jan 3 12:02:45 bras1 kernel: usbus1: <Intel PCH USB 2.0 controller USB-A> on ehci1 Jan 3 12:02:45 bras1 kernel: pcib7: <ACPI PCI-PCI bridge> at device 30.0 on pci0 Jan 3 12:02:45 bras1 kernel: pci7: <ACPI PCI bus> on pcib7 Jan 3 12:02:45 bras1 kernel: em0: <Intel® PRO/1000 Legacy Network Connection 1.0.3> port 0xec00-0xec3f mem 0xf7fe0000-0xf7ffffff,0xf7fc0000-0xf7fdffff irq Jan 3 12:02:45 bras1 kernel: em0: [FILTER] Jan 3 12:02:45 bras1 kernel: em0: Ethernet address: 00:1b:21:6e:a6:55 Jan 3 12:02:45 bras1 kernel: em1: <Intel® PRO/1000 Legacy Network Connection 1.0.3> port 0xe880-0xe8bf mem 0xf7f80000-0xf7f9ffff,0xf7f60000-0xf7f7ffff irq Jan 3 12:02:45 bras1 kernel: em1: [FILTER] Jan 3 12:02:45 bras1 kernel: em1: Ethernet address: 00:1b:21:6e:a6:41 Jan 3 12:02:45 bras1 kernel: isab0: <PCI-ISA bridge> at device 31.0 on pci0 Jan 3 12:02:45 bras1 kernel: isa0: <ISA bus> on isab0 Jan 3 12:02:45 bras1 kernel: atapci1: <Intel 5 Series/3400 Series PCH SATA300 controller> port 0xac00-0xac07,0xa880-0xa883,0xa800-0xa807,0xa480-0xa483,0xa40 Jan 3 12:02:45 bras1 kernel: atapci1: [iTHREAD] Jan 3 12:02:45 bras1 kernel: ata4: <ATA channel 0> on atapci1 Jan 3 12:02:45 bras1 kernel: ata4: [iTHREAD] Jan 3 12:02:45 bras1 kernel: ata5: <ATA channel 1> on atapci1 Jan 3 12:02:45 bras1 kernel: ata5: [iTHREAD] Jan 3 12:02:45 bras1 kernel: pci0: <serial bus, SMBus> at device 31.3 (no driver attached) Jan 3 12:02:45 bras1 kernel: atapci2: <Intel 5 Series/3400 Series PCH SATA300 controller> port 0xbc00-0xbc07,0xb880-0xb883,0xb800-0xb807,0xb480-0xb483,0xb40 Jan 3 12:02:45 bras1 kernel: atapci2: [iTHREAD] Jan 3 12:02:45 bras1 kernel: ata6: <ATA channel 0> on atapci2 Jan 3 12:02:45 bras1 kernel: ata6: [iTHREAD] Jan 3 12:02:45 bras1 kernel: ata7: <ATA channel 1> on atapci2 Jan 3 12:02:45 bras1 kernel: ata7: [iTHREAD] Jan 3 12:02:45 bras1 kernel: acpi_button0: <Power Button> on acpi0 Jan 3 12:02:45 bras1 kernel: atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0 Jan 3 12:02:45 bras1 kernel: acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0 Jan 3 12:02:45 bras1 kernel: Timecounter "HPET" frequency 14318180 Hz quality 900 Jan 3 12:02:45 bras1 kernel: uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 Jan 3 12:02:45 bras1 kernel: uart0: [FILTER] Jan 3 12:02:45 bras1 kernel: atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0 Jan 3 12:02:45 bras1 kernel: atkbd0: <AT Keyboard> irq 1 on atkbdc0 Jan 3 12:02:45 bras1 kernel: kbd0 at atkbd0 Jan 3 12:02:45 bras1 kernel: atkbd0: [GIANT-LOCKED] Jan 3 12:02:45 bras1 kernel: atkbd0: [iTHREAD] Jan 3 12:02:45 bras1 kernel: psm0: <PS/2 Mouse> irq 12 on atkbdc0 Jan 3 12:02:45 bras1 kernel: psm0: [GIANT-LOCKED] Jan 3 12:02:45 bras1 kernel: psm0: [iTHREAD] Jan 3 12:02:45 bras1 kernel: psm0: model IntelliMouse Explorer, device ID 4 Jan 3 12:02:45 bras1 kernel: orm0: <ISA Option ROMs> at iomem 0xc0000-0xcefff,0xcf000-0xcffff,0xd0000-0xd0fff on isa0 Jan 3 12:02:45 bras1 kernel: sc0: <System console> at flags 0x100 on isa0 Jan 3 12:02:45 bras1 kernel: sc0: VGA <16 virtual consoles, flags=0x300> Jan 3 12:02:45 bras1 kernel: vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0 Jan 3 12:02:45 bras1 kernel: est0: <Enhanced SpeedStep Frequency Control> on cpu0 Jan 3 12:02:45 bras1 kernel: p4tcc0: <CPU Frequency Thermal Control> on cpu0 Jan 3 12:02:45 bras1 kernel: est1: <Enhanced SpeedStep Frequency Control> on cpu1 Jan 3 12:02:45 bras1 kernel: p4tcc1: <CPU Frequency Thermal Control> on cpu1 Jan 3 12:02:45 bras1 kernel: est2: <Enhanced SpeedStep Frequency Control> on cpu2 Jan 3 12:02:45 bras1 kernel: p4tcc2: <CPU Frequency Thermal Control> on cpu2 Jan 3 12:02:45 bras1 kernel: est3: <Enhanced SpeedStep Frequency Control> on cpu3 Jan 3 12:02:45 bras1 kernel: p4tcc3: <CPU Frequency Thermal Control> on cpu3 Jan 3 12:02:45 bras1 kernel: Timecounters tick every 1.000 msec Jan 3 12:02:45 bras1 kernel: ipfw2 initialized, divert loadable, nat loadable, rule-based forwarding enabled, default to deny, logging disabled Jan 3 12:02:45 bras1 kernel: usbus0: 480Mbps High Speed USB v2.0 Jan 3 12:02:45 bras1 kernel: usbus1: 480Mbps High Speed USB v2.0 Jan 3 12:02:45 bras1 kernel: ad8: 114497MB <SAMSUNG SP1213C SV100-30> at ata4-master UDMA100 SATA 1.5Gb/s Jan 3 12:02:45 bras1 kernel: ugen0.1: <Intel> at usbus0 Jan 3 12:02:45 bras1 kernel: uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0 Jan 3 12:02:45 bras1 kernel: ugen1.1: <Intel> at usbus1 Jan 3 12:02:45 bras1 kernel: uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 Jan 3 12:02:45 bras1 kernel: SMP: AP CPU #1 Launched! Jan 3 12:02:45 bras1 kernel: SMP: AP CPU #2 Launched! Jan 3 12:02:45 bras1 kernel: SMP: AP CPU #3 Launched! Jan 3 12:02:45 bras1 kernel: GEOM_JOURNAL: Journal 3140362783: ad8s1a contains data. Jan 3 12:02:45 bras1 kernel: GEOM_JOURNAL: Journal 3140362783: ad8s1a contains journal. Jan 3 12:02:45 bras1 kernel: GEOM_JOURNAL: Journal ad8s1a consistent. Jan 3 12:02:45 bras1 kernel: GEOM_JOURNAL: Journal 2597746777: ad8s1d contains data. Jan 3 12:02:45 bras1 kernel: GEOM_JOURNAL: Journal 2597746777: ad8s1d contains journal. Jan 3 12:02:45 bras1 kernel: GEOM_JOURNAL: Journal ad8s1d consistent. Jan 3 12:02:45 bras1 kernel: GEOM_JOURNAL: Journal 2136003222: ad8s1e contains data. Jan 3 12:02:45 bras1 kernel: GEOM_JOURNAL: Journal 2136003222: ad8s1e contains journal. Jan 3 12:02:45 bras1 kernel: GEOM_JOURNAL: Journal ad8s1e consistent. Jan 3 12:02:45 bras1 kernel: GEOM_JOURNAL: Journal 2852105731: ad8s1f contains data. Jan 3 12:02:45 bras1 kernel: GEOM_JOURNAL: Journal 2852105731: ad8s1f contains journal. Jan 3 12:02:45 bras1 kernel: GEOM_JOURNAL: Journal ad8s1f consistent. Jan 3 12:02:45 bras1 kernel: GEOM_JOURNAL: Journal 2006152971: ad8s1g contains data. Jan 3 12:02:45 bras1 kernel: GEOM_JOURNAL: Journal 2006152971: ad8s1g contains journal. Jan 3 12:02:45 bras1 kernel: GEOM_JOURNAL: Journal ad8s1g consistent. Jan 3 12:02:45 bras1 kernel: Root mount waiting for: usbus1 usbus0 Jan 3 12:02:45 bras1 kernel: uhub0: 2 ports with 2 removable, self powered Jan 3 12:02:45 bras1 kernel: uhub1: 2 ports with 2 removable, self powered Jan 3 12:02:45 bras1 kernel: Root mount waiting for: usbus1 usbus0 Jan 3 12:02:45 bras1 kernel: ugen0.2: <vendor 0x8087> at usbus0 Jan 3 12:02:45 bras1 kernel: uhub2: <vendor 0x8087 product 0x0020, class 9/0, rev 2.00/0.00, addr 2> on usbus0 Jan 3 12:02:45 bras1 kernel: ugen1.2: <vendor 0x8087> at usbus1 Jan 3 12:02:45 bras1 kernel: uhub3: <vendor 0x8087 product 0x0020, class 9/0, rev 2.00/0.00, addr 2> on usbus1 Jan 3 12:02:45 bras1 kernel: uhub2: 6 ports with 6 removable, self powered Jan 3 12:02:45 bras1 kernel: uhub3: 8 ports with 8 removable, self powered Jan 3 12:02:45 bras1 kernel: ugen1.3: <POWERCOM Co.,LTD> at usbus1 Jan 3 12:02:45 bras1 kernel: uhid0: <POWERCOM Co.,LTD HID UPS Battery, class 0/0, rev 1.10/0.01, addr 3> on usbus1 Jan 3 12:02:45 bras1 kernel: Trying to mount root from ufs:/dev/ufs/br1root Jan 3 12:02:45 bras1 kernel: WARNING: / was not properly dismounted Jan 3 12:02:47 bras1 kernel: em0: link state changed to UP Jan 3 12:02:47 bras1 kernel: em1: link state changed to UP Jan 3 12:02:47 bras1 kernel: vlan17: link state changed to UP Jan 3 12:02:47 bras1 kernel: vlan16: link state changed to UP Jan 3 12:02:47 bras1 kernel: vlan19: link state changed to UP Jan 3 12:02:47 bras1 kernel: vlan18: link state changed to UP Jan 3 12:02:47 bras1 kernel: vlan0: link state changed to UP Jan 3 12:02:47 bras1 kernel: vlan1: link state changed to UP Jan 3 12:02:47 bras1 kernel: vlan15: link state changed to UP Jan 3 12:02:48 bras1 dhcpd: Jan 3 12:02:48 bras1 kernel: 12 Jan 3 12:02:48 bras1 dhcpd: No subnet declaration for vlan1 (10.10.0.254). Jan 3 12:02:48 bras1 dhcpd: ** Ignoring requests on vlan1. If this is not what Jan 3 12:02:48 bras1 dhcpd: you want, please write a subnet declaration Jan 3 12:02:48 bras1 dhcpd: in your dhcpd.conf file for the network segment Jan 3 12:02:48 bras1 dhcpd: to which interface vlan1 is attached. ** Jan 3 12:02:48 bras1 dhcpd: Jan 3 12:02:48 bras1 dhcpd: Jan 3 12:02:48 bras1 dhcpd: No subnet declaration for em1 (no IPv4 addresses). Jan 3 12:02:48 bras1 dhcpd: ** Ignoring requests on em1. If this is not what Jan 3 12:02:48 bras1 dhcpd: you want, please write a subnet declaration Jan 3 12:02:48 bras1 dhcpd: in your dhcpd.conf file for the network segment Jan 3 12:02:48 bras1 dhcpd: to which interface em1 is attached. ** Jan 3 12:02:48 bras1 dhcpd: Jan 3 12:02:48 bras1 dhcpd: Jan 3 12:02:48 bras1 dhcpd: No subnet declaration for em0 (10.100.100.1). Jan 3 12:02:48 bras1 dhcpd: ** Ignoring requests on em0. If this is not what Jan 3 12:02:48 bras1 dhcpd: you want, please write a subnet declaration Jan 3 12:02:48 bras1 dhcpd: in your dhcpd.conf file for the network segment Jan 3 12:02:48 bras1 dhcpd: to which interface em0 is attached. ** Jan 3 12:02:48 bras1 dhcpd: Еще в логах начали появляться такие сообщения: Jan 2 12:18:38 bras1 kernel: Limiting icmp ping response from 4624 to 200 packets/sec Jan 2 12:26:37 bras1 kernel: Limiting icmp ping response from 224 to 200 packets/sec Jan 2 12:26:40 bras1 kernel: Limiting icmp ping response from 301 to 200 packets/sec Jan 2 12:26:44 bras1 kernel: Limiting icmp ping response from 1001 to 200 packets/sec Jan 2 12:26:45 bras1 kernel: Limiting icmp ping response from 4545 to 200 packets/sec Jan 2 12:26:46 bras1 kernel: Limiting icmp ping response from 4329 to 200 packets/sec Jan 2 12:26:47 bras1 kernel: Limiting icmp ping response from 4684 to 200 packets/sec Jan 2 12:26:48 bras1 kernel: Limiting icmp ping response from 3863 to 200 packets/sec Jan 2 12:26:54 bras1 kernel: Limiting icmp ping response from 2575 to 200 packets/sec Jan 2 12:26:55 bras1 kernel: Limiting icmp ping response from 4302 to 200 packets/sec Jan 2 12:26:56 bras1 kernel: Limiting icmp ping response from 4552 to 200 packets/sec Кто то балуется с сети? Ссылка на сообщение Поделиться на других сайтах
Demeo 29 Опубліковано: 2013-01-03 12:11:26 Share Опубліковано: 2013-01-03 12:11:26 Похоже на роутер Ссылка на сообщение Поделиться на других сайтах
rootvm 1 Опубліковано: 2013-01-03 19:58:25 Share Опубліковано: 2013-01-03 19:58:25 net.inet.tcp.blackhole=2 net.inet.udp.blackhole=1 Здесь два варианта сканят или Ddos. Еще сетевая может у кого то флудить. Ссылка на сообщение Поделиться на других сайтах
Рекомендованные сообщения
Создайте аккаунт или войдите в него для комментирования
Вы должны быть пользователем, чтобы оставить комментарий
Создать аккаунт
Зарегистрируйтесь для получения аккаунта. Это просто!
Зарегистрировать аккаунтВхід
Уже зарегистрированы? Войдите здесь.
Войти сейчас