Jump to content

LACP Cisco3550 & mes2324fb

Shuher

By Shuher,
in Switch Layer 2

 Share Followers 1

Recommended Posts

Shuher

Shuher 216

Posted
Posted

Доброго дня!
Не могу настроить LACP между Cisco3550 и mes2324fb.
mes2324fb:

console#show running-config interface Port-Channel 1
interface Port-channel1
speed 1000
switchport mode trunk
switchport trunk allowed vlan add 73
!
console#show running-config interface GigabitEthernet 0/15
interface gigabitethernet1/0/15
description LACP_CISOC
lacp timeout short
lacp port-priority 12
channel-group 1 mode auto
switchport mode trunk
!
console#show running-config interface GigabitEthernet 0/16
interface gigabitethernet1/0/16
description LACP_CISOC
lacp timeout short
lacp port-priority 13
channel-group 1 mode auto
switchport mode trunk
!


Cisco3550:

Switch#show running-config interface port-channel 2
interface Port-channel2
description LACP_ELTEX4+9
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 73
switchport mode trunk
end
Switch#show running-config interface gigabitEthernet 0/4
interface GigabitEthernet0/4
description LACP-ELTEX
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 73
switchport mode trunk
no cdp enable
channel-protocol lacp
channel-group 2 mode passive
end
Switch#show running-config interface gigabitEthernet 0/9
interface GigabitEthernet0/9
description LACP-ELTEX
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 73
switchport mode trunk
no cdp enable
channel-protocol lacp
channel-group 2 mode passive
end


Подскажите, что не так делаю!
Спасибо!

Link to post
Share on other sites
karyon

karyon 48

Posted
Posted

На циске попробуйте mode active включить.

На mez на портах нет команды о 73 влане которая есть на портченеле - нормально ли это для этого свича?

На циске можно включить debug lacp и посмотреть что там происходит

Link to post
Share on other sites
Shuher

Shuher 216

Posted
  • Author
Posted (edited)

На циске попробуйте mode active включить.

На mez на портах нет команды о 73 влане которая есть на портченеле - нормально ли это для этого свича?

На циске можно включить debug lacp и посмотреть что там происходит

 
Не хочет влан прибивать на порт:
console(config)#interface GigabitEthernet 0/15
console(config-if)#switchport trunk allowed vlan add 73
Port gi1/0/15 belongs to a port-channel.

 

 

Вот включил дебаг:

 

Log Buffer (4096 bytes):
: lacp_send_lacpdu: (Gi0/9) About to send the 110 LACPDU
Apr 16 13:33:31.687: LACP: lacp_write: LACP 124 bytes out Gi0/9
Apr 16 13:33:32.019: LACP: lacp_insert_partner_cd_inhibitor: didn't change sync flag.
Apr 16 13:33:32.019: LACP: lacp_send_lacpdu: (Gi0/4) About to send the 110 LACPDU
Apr 16 13:33:32.019: LACP: lacp_write: LACP 124 bytes out Gi0/4
Apr 16 13:33:47.848: LACP: lacp_insert_partner_cd_inhibitor: didn't change sync flag.
Apr 16 13:33:47.848: LACP: lacp_send_lacpdu: (Gi0/2) About to send the 110 LACPDU
Apr 16 13:33:47.848: LACP: lacp_write: LACP 124 bytes out Gi0/2
Apr 16 13:33:51.996: LACP: lacp_insert_partner_cd_inhibitor: didn't change sync flag.
Apr 16 13:33:51.996: LACP: lacp_send_lacpdu: (Gi0/3) About to send the 110 LACPDU
Apr 16 13:33:51.996: LACP: lacp_write: LACP 124 bytes out Gi0/3
Apr 16 13:33:58.296: LACP: lacp_insert_partner_cd_inhibitor: didn't change sync flag.
Apr 16 13:33:58.296: LACP: lacp_send_lacpdu: (Gi0/4) About to send the 110 LACPDU
Apr 16 13:33:58.296: LACP: lacp_write: LACP 124 bytes out Gi0/4
Apr 16 13:34:01.316: LACP: lacp_insert_partner_cd_inhibitor: didn't change sync flag.
Apr 16 13:34:01.316: LACP: lacp_send_lacpdu: (Gi0/9) About to send the 110 LACPDU
Apr 16 13:34:01.316: LACP: lacp_write: LACP 124 bytes out Gi0/9
Apr 16 13:34:15.728: LACP: lacp_insert_partner_cd_inhibitor: didn't change sync flag.
Apr 16 13:34:15.728: LACP: lacp_send_lacpdu: (Gi0/2) About to send the 110 LACPDU
Apr 16 13:34:15.728: LACP: lacp_write: LACP 124 bytes out Gi0/2
Apr 16 13:34:19.173: LACP: lacp_hw_off: Gi0/4 is going down
 
Apr 16 13:34:19.173: LACP: if_down: Gi0/4
Apr 16 13:34:19.173: LACP: lacp_hw_off: send pdu out Gi0/4
Apr 16 13:34:19.173: LACP: lacp_insert_partner_cd_inhibitor: didn't change sync flag.
Apr 16 13:34:19.173: LACP: lacp_send_lacp_off: (Gi0/4) About to send the 110 LACPDU
Apr 16 13:34:19.177: LACP: lacp_write: LACP 124 bytes out Gi0/4
Apr 16 13:34:19.225: LACP: lacp_hw_off: Gi0/9 is going down
 
Apr 16 13:34:19.225: LACP: if_down: Gi0/9
Apr 16 13:34:19.225: LACP: lacp_hw_off: send pdu out Gi0/9
Apr 16 13:34:19.225: LACP: lacp_insert_partner_cd_inhibitor: didn't change sync flag.
Apr 16 13:34:19.225: LACP: lacp_send_lacp_off: (Gi0/9) About to send the 110 LACPDU
Apr 16 13:34:19.225: LACP: lacp_write: LACP 124 bytes out Gi0/9
Apr 16 13:34:20.221: %LINEPROTO-5-UPDOWN: Line protocol on Interface Port-channel2, changed state to down
Apr 16 13:34:20.613: LACP: lacp_insert_partner_cd_inhibitor: didn't change sync flag.
Apr 16 13:34:20.613: LACP: lacp_send_lacpdu: (Gi0/3) About to send the 110 LACPDU
Apr 16 13:34:20.613: LACP: lacp_write: LACP 124 bytes out Gi0/3
Apr 16 13:34:21.129: %LINK-5-CHANGED: Interface GigabitEthernet0/4, changed state to administratively down
Apr 16 13:34:21.193: %LINK-5-CHANGED: Interface GigabitEthernet0/9, changed state to administratively down
Apr 16 13:34:21.225: %LINK-5-CHANGED: Interface Port-channel2, changed state to administratively down
Apr 16 13:34:22.129: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/4, changed state to down
Apr 16 13:34:22.229: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/9, changed state to down
Apr 16 13:34:22.593: %GBIC-4-UNRECOGNIZED_EXTTYPE: GBIC interface Gi0/4 has unrecognized extended type
Apr 16 13:34:24.149: %GBIC-4-UNRECOGNIZED_EXTTYPE: GBIC interface Gi0/4 has unrecognized extended type
Apr 16 13:34:24.373: %LINK-3-UPDOWN: Interface Port-channel2, changed state to down
Apr 16 13:34:24.373: %LINK-3-UPDOWN: Interface GigabitEthernet0/4, changed state to up
Apr 16 13:34:24.377: %LINK-3-UPDOWN: Interface GigabitEthernet0/9, changed state to up
Apr 16 13:34:24.901: %SYS-5-CONFIG_I: Configured from console by vty6 (192.168.22.81)
Apr 16 13:34:26.945: %EC-5-CANNOT_BUNDLE2: Gi0/9 is not compatible with Po2 and will be suspended (vlan mask is different)
Apr 16 13:34:26.945: LACP: lacp_port_unsuitable: Gi0/9
Apr 16 13:34:27.149: %EC-5-CANNOT_BUNDLE2: Gi0/4 is not compatible with Po2 and will be suspended (vlan mask is different)
Apr 16 13:34:27.149: LACP: lacp_port_unsuitable: Gi0/4
 
Edited by Shuher
Link to post
Share on other sites
l1ght

l1ght 377

Posted
Posted 
cisco#show run int po1
Building configuration...

Current configuration : 143 bytes
!
interface Port-channel1
 switchport
 switchport trunk encapsulation dot1q
 switchport trunk allowed vlan 10,20
 switchport mode trunk
end
ciscor#show run int gi1/1
Building configuration...

Current configuration : 188 bytes
!
interface GigabitEthernet1/1
 switchport trunk encapsulation dot1q
 switchport trunk allowed vlan 10,20
 switchport mode trunk
 channel-group 1 mode active
end

cisco#show run int gi1/2
Building configuration...

Current configuration : 188 bytes
!
interface GigabitEthernet1/2
 switchport trunk encapsulation dot1q
 switchport trunk allowed vlan 10,20
 switchport mode trunk
 channel-group 1 mode active
end

кусок рабочей конфиги

Link to post
Share on other sites
Mikca

Mikca 1

Posted
Posted

 

Попробуйте для начала скопипастить из инструкции http://docplayer.ru/39495965-Mes5324-mes3324-mes2324-mes2348.html

Это я читал. Не помогло!

 

Ох уж эти читатели..

show lacp port-channel [group] Показывает информацию о протоколе LACP для группы портов.

Совет пробовали?

 

На циске попробуйте mode active включить.

Link to post
Share on other sites
Shuher

Shuher 216

Posted
  • Author
Posted

 

 

Попробуйте для начала скопипастить из инструкции http://docplayer.ru/39495965-Mes5324-mes3324-mes2324-mes2348.html

Это я читал. Не помогло!

 

Ох уж эти читатели..

show lacp port-channel [group] Показывает информацию о протоколе LACP для группы портов.

Совет пробовали?

 

На циске попробуйте mode active включить.

 

Совет пробовал. Выхлоп выше вашего поста

Link to post
Share on other sites
Mikca

Mikca 1

Posted
Posted (edited)

 

 

 

Попробуйте для начала скопипастить из инструкции http://docplayer.ru/39495965-Mes5324-mes3324-mes2324-mes2348.html

Это я читал. Не помогло!

 

Ох уж эти читатели..

show lacp port-channel [group] Показывает информацию о протоколе LACP для группы портов.

Совет пробовали?

 

На циске попробуйте mode active включить.

 

Совет пробовал. Выхлоп выше вашего поста

 

На елтексе сделайте show lacp port-channel [group]

 

На циске вы точно включили mode active ?

 

Свой же лог читали?

 

 

 

 

Вот включил дебаг:

 

 
Apr 16 13:34:21.129: %LINK-5-CHANGED: Interface GigabitEthernet0/4, changed state to administratively down
Apr 16 13:34:21.193: %LINK-5-CHANGED: Interface GigabitEthernet0/9, changed state to administratively down
Apr 16 13:34:21.225: %LINK-5-CHANGED: Interface Port-channel2, changed state to administratively down
Apr 16 13:34:22.129: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/4, changed state to down
Apr 16 13:34:22.229: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/9, changed state to down
Apr 16 13:34:22.593: %GBIC-4-UNRECOGNIZED_EXTTYPE: GBIC interface Gi0/4 has unrecognized extended type
Apr 16 13:34:24.149: %GBIC-4-UNRECOGNIZED_EXTTYPE: GBIC interface Gi0/4 has unrecognized extended type
Apr 16 13:34:24.373: %LINK-3-UPDOWN: Interface Port-channel2, changed state to down
Apr 16 13:34:24.373: %LINK-3-UPDOWN: Interface GigabitEthernet0/4, changed state to up
Apr 16 13:34:24.377: %LINK-3-UPDOWN: Interface GigabitEthernet0/9, changed state to up
Apr 16 13:34:24.901: %SYS-5-CONFIG_I: Configured from console by vty6 (192.168.22.81)
Apr 16 13:34:26.945: %EC-5-CANNOT_BUNDLE2: Gi0/9 is not compatible with Po2 and will be suspended (vlan mask is different)
Apr 16 13:34:26.945: LACP: lacp_port_unsuitable: Gi0/9
Apr 16 13:34:27.149: %EC-5-CANNOT_BUNDLE2: Gi0/4 is not compatible with Po2 and will be suspended (vlan mask is different)
Apr 16 13:34:27.149: LACP: lacp_port_unsuitable: Gi0/4
 

 

Edited by Mikca
Link to post
Share on other sites
karyon

karyon 48

Posted
Posted (edited)
console(config)#interface GigabitEthernet 0/15
console(config-if)#switchport trunk allowed vlan add 73
Port gi1/0/15 belongs to a port-channel.

 

 

Разберите портченел, потом пропишите влан на порт, потом соберите портченел.

По идее, настройки, что на портах, что на портченел в итоге должны быть одинаковы
Edited by karyon
Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Followers 1
Go to topic listing

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...