Перейти до

BDCOM P3310C


Kto To

Рекомендованные сообщения

  В 02.10.2017 в 07:13, PolyComm сказав:

Доброго времени суток.

2 недели назад перепрошили BDCOM p3310c на новую версию прошивки BD_3310C_10.1.0E_43480_en .

И было замечено несколько (пока что) неприятных багов (если это они) , а именно : после перезагрузки абон ону ( перезагрузить по питанию) ОНУ BDCOM p1501c1 или p1501b1 подтягивают не верную конфигурация , привязка по acl , по внутренему айпи, и по других вланах. Приходиться править в ручную каждый раз.... кто то с таким сталкивался или может посоветовать в чем может быть проблема?

Заранее спасибо

покажите сам темплейт ... может быть есть команды без СТС ?

Ссылка на сообщение
Поделиться на других сайтах
  • Відповіді 934
  • Створено
  • Остання відповідь

Top Posters In This Topic

Top Posters In This Topic

Popular Posts

Вчи українську, це тобі ще знадобиться!

Дуже схоже на "фільтр по МАС", який зявився в 3310с. ftp://ftp.romsat.ua/pub/Lan/BDCOM/P3310C/Read_before_Update.txt All mac addresses that fit the mask below will be dropped on OLT PON inte

Блин, да поставьте Вы в конце концов понконтрол и собирайте сигналы по СНМП и не мучайтесь

Posted Images

На старые онушки вот такой конфиг :

interface epon0/3:43
 onu-configuration
epon sla upstream pir 45000 cir 1000
epon sla downstream pir 45000 cir 1000
epon onu port 1 ctc vlan mode tag 150
epon onu ip address static 192.168.12.133 255.255.255.0 gateway 192.168.12.1 vlan 1
epon onu port 1  loopback detect
epon onu port 1 ctc rate-limit 45000 egress
epon onu port 1 ctc rate-limit 45000 ingress
epon onu port 1 ip access-group acl343
!!onu-configuration-end
!

а для новых 
p1501d1

interface epon0/3:45
 onu-configuration
epon sla upstream pir 45000 cir 1000
epon sla downstream pir 45000 cir 1000
epon onu port 1 ctc vlan mode tag 150
epon onu ctc ip address static 192.168.12.113 255.255.255.0 gateway 192.168.12.1 cvlan 1 svlan 0 priority 0
epon onu port 1 ctc loopback detect
epon onu port 1 ctc rate-limit 45000 egress
epon onu port 1 ctc rate-limit 45000 ingress
epon onu port 1 ip access-group acl345
!!onu-configuration-end
!

Для новых онушек нужно было добавлять ctc в 2-х строках....
Может нужно переписать конфиги для старых онушек как на новых?

Ссылка на сообщение
Поделиться на других сайтах

Why you make double shaper ?

One at the onu side and one at the olt side ?

Better remove this:

epon onu port 1 ctc rate-limit 45000 egress

epon onu port 1 ctc rate-limit 45000 ingress
Also paste your template.
Here is mine:
--------
epon onu-config-template T1
 cmd-sequence 001 epon onu all-port ctc vlan mode tag 214
 cmd-sequence 002 epon onu all-port ctc notify link
 cmd-sequence 003 epon onu all-port ctc loopback detect
 cmd-sequence 004 epon onu all-port ctc notify loopback
 cmd-sequence 005 epon onu ctc fec
 cmd-sequence 006 epon fec enable
 cmd-sequence 007 no epon onu all-port ctc rate-limit ingress
 cmd-sequence 008 no epon onu all-port ctc rate-limit egress
 cmd-sequence 009 epon sla upstream pir 100000 cir 12000
 cmd-sequence 010 epon sla downstream pir 100000 cir 12000
-----
 
And also connect template to epon port like that:
.....
interface EPON0/1
 description pon-1
 epon pre-config-template T1 binded-onu-llid 1-64
.....
Ссылка на сообщение
Поделиться на других сайтах

Добрый день.

Нашел в логах причину своей проблемы с дёрганием EPON-портов:

 

 

  Відновити прихований контент

 

 

Всё, что смог нагуглить по этой проблеме - это ссылку на соседнюю тему по p3600

Там проблема решилась заливкой нового загрузчика (tiger.blob)

 

Кто-нибудь может поделиться посвежее загрузчиком, чем Version 0.4.1?

ponfive-01#sh ver
BDCOM(tm) P3310C Software, Version 10.1.0E Build 43480
Copyright by Shanghai Baud Data Communication CO. LTD.
Compiled: 2017-6-6 16:43:18 by SYS, Image text-base: 0x80008000
ROM: System Bootstrap, Version 0.4.1, Serial num:00316001396
System image file is "Switch.bin"                                                                                                                                                                                                            
hardware version:V1.0                                                                                                                                                                                                                        
(RISC) processor with 131072K bytes of memory, 16384K bytes of flash                                                                                                                                                                         
Base ethernet MAC Address: 84:79:73:5b:26:d4                                                                                                                                                                                                 
snmp info:                                                                                                                                                                                                                                   
  product_ID:294   system_ID:1.3.6.1.4.1.3320.1.294.0                                                                                                                                                                                        
ponfive-01 uptime is 2:22:41:25, The current time: 2017-10-2 12:55:7
ponfive-02#sh ver
BDCOM(tm) P3310C Software, Version 10.1.0E Build 43480
Copyright by Shanghai Baud Data Communication CO. LTD.
Compiled: 2017-6-6 16:43:18 by SYS, Image text-base: 0x80008000
ROM: System Bootstrap, Version 0.4.1, Serial num:00316004687
System image file is "Switch.bin"
hardware version:V1.0
(RISC) processor with 131072K bytes of memory, 16384K bytes of flash
Base ethernet MAC Address: 84:79:73:5b:da:ce
snmp info:
  product_ID:294   system_ID:1.3.6.1.4.1.3320.1.294.0
ponfive-02 uptime is 2:22:41:43, The current time: 2017-10-2 12:55:22
Ссылка на сообщение
Поделиться на других сайтах

Hello,

I do not have that problem.

My version is the same:

 

# show ver

BDCOM P3310C Software, Version 10.1.0E Build 43480
Copyright by Shanghai Baud Data Communication CO. LTD.
Compiled: 2017-6-6 16:43:18 by SYS, Image text-base: 0x80008000
ROM: System Bootstrap, Version 0.4.1, Serial num:xxxxxxxxxxx
System image file is "Switch.bin"
hardware version:V1.0
(RISC) processor with 131072K bytes of memory, 16384K bytes of flash
Base ethernet MAC Address: xx:xx:xx:xx:xx:xx
snmp info:
  product_ID:xxx   system_ID:1.3.6.1.4.1.3320.1.xxx.0
 
Maybe you have hardware problem or faulty sfp ?
Try to change it.
Also can you supply your configuration ?
Ссылка на сообщение
Поделиться на других сайтах
  В 04.09.2017 в 18:57, MasMaster сказав:

 

  В 04.09.2017 в 18:54, Fallen_Grayswandir сказав:

Та ну их нафик. Прошивать головы ревизии С надо по принципу: "Работает? Не трогай!"

 

 

 

так не работает :(

 

warnings(4) SEP 4 21:55:39 timestamp 0, window 0, threshold 0, value 0
warnings(4) SEP 4 21:55:39 Alarm LASER_ALWAYS_ON from OLT 0x03000000 port EPON0/1 pon_diID 7
warnings(4) SEP 4 21:55:39 timestamp 0, window 0, threshold 0, value 0
warnings(4) SEP 4 21:55:39 Alarm LASER_ALWAYS_ON from OLT 0x03000000 port EPON0/1 pon_diID 7
warnings(4) SEP 4 21:54:39 timestamp 0, window 0, threshold 0, value 0
warnings(4) SEP 4 21:54:39 Alarm LASER_ALWAYS_ON from OLT 0x03000000 port EPON0/1 pon_diID 7
warnings(4) SEP 4 21:54:39 timestamp 0, window 0, threshold 0, value 0
warnings(4) SEP 4 21:54:39 Alarm LASER_ALWAYS_ON from OLT 0x03000000 port EPON0/1 pon_diID 7
warnings(4) SEP 4 21:53:39 timestamp 0, window 0, threshold 0, value 0
warnings(4) SEP 4 21:53:39 Alarm LASER_ALWAYS_ON from OLT 0x03000000 port EPON0/1 pon_diID 7
warnings(4) SEP 4 21:53:39 timestamp 0, window 0, threshold 0, value 0
warnings(4) SEP 4 21:53:39 Alarm LASER_ALWAYS_ON from OLT 0x03000000 port EPON0/1 pon_diID 7

 

все перемеряли, все онушки поменяли, модуль тоже меняли....

 

Добрый день.

Точно такая же проблема...

Oct  2 14:50:58 timestamp 0, window 0, threshold 0, value 0
Oct  2 14:50:58 Alarm LASER_ALWAYS_ON from OLT 0x03000000 port EPON0/3 pon_diID 9
Oct  2 14:50:58 timestamp 0, window 0, threshold 0, value 0
Oct  2 14:50:58 Alarm LASER_ALWAYS_ON from OLT 0x03000000 port EPON0/3 pon_diID 9
Oct  2 14:50:57 User admin enter privilege mode from vty 0, level = 15
Oct  2 14:49:58 timestamp 0, window 0, threshold 0, value 0
Oct  2 14:49:58 Alarm LASER_ALWAYS_ON from OLT 0x03000000 port EPON0/3 pon_diID 9
Oct  2 14:49:58 timestamp 0, window 0, threshold 0, value 0
Oct  2 14:49:58 Alarm LASER_ALWAYS_ON from OLT 0x03000000 port EPON0/3 pon_diID 9
Oct  2 14:48:58 timestamp 0, window 0, threshold 0, value 0
Oct  2 14:48:58 Alarm LASER_ALWAYS_ON from OLT 0x03000000 port EPON0/3 pon_diID 9
 
 

Если разберетесь, отпишитесь пожалуйста, а то тоже не знаем куда копать...

Відредаговано dsredline
Ссылка на сообщение
Поделиться на других сайтах
  В 02.10.2017 в 10:13, sanitariu сказав:

 

Hello,

I do not have that problem.

My version is the same:

 

# show ver

BDCOM P3310C Software, Version 10.1.0E Build 43480
Copyright by Shanghai Baud Data Communication CO. LTD.
Compiled: 2017-6-6 16:43:18 by SYS, Image text-base: 0x80008000
ROM: System Bootstrap, Version 0.4.1, Serial num:xxxxxxxxxxx
System image file is "Switch.bin"
hardware version:V1.0
(RISC) processor with 131072K bytes of memory, 16384K bytes of flash
Base ethernet MAC Address: xx:xx:xx:xx:xx:xx
snmp info:
  product_ID:xxx   system_ID:1.3.6.1.4.1.3320.1.xxx.0
 
Maybe you have hardware problem or faulty sfp ?
Try to change it.
Also can you supply your configuration ?

 

 

Hi. I have three different OLT, that have been bought during last year, and different sfp's on it.

And that problem begins, when I upgraded my firmware.

So I don't think, that problem is on hardware.

 

My configuration. (they are similar for all OLTs)

 

 

  Відновити прихований контент

 

Відредаговано Fallen_Grayswandir
Ссылка на сообщение
Поделиться на других сайтах

Hi,

I do not see anything strange. You are using multicasts.

May be try to raise storm filters.

Also on new versions you must enable this command:

"epon local-mac forward"

Although you do not have mac addresses like: X2:XX:XX:XX:XX:XX,X6:XX:XX:XX:XX:XX, XA:XX:XX:XX:XX:XX, XE:XX:XX:XX:XX:XX

Some day you can buy such onus and they will make disconnects. This is another BDCOM trick to try making their OLTs work only with

bdcom onus.

Also this is the correct oams:

epon oam-version 1 0x30

epon oam-version 2 0x21
epon oam-version 3 0x20
 
You can change them.
You can try to enable the following on the Epon interfaces:
 
 epon fec-rx
 epon fec-tx
 epon optical-transceiver power-tx high-limit enable threshold 70 30
 epon optical-transceiver power-tx low-limit enable threshold 20 20
 epon optical-transceiver temperature high-limit enable threshold 500 400
 epon optical-transceiver temperature low-limit enable threshold -1280 -400
 epon optical-transceiver voltage high-limit enable threshold 30 25
 epon optical-transceiver voltage low-limit enable threshold 0 10
 epon optical-transceiver current high-limit enable threshold 1310 800
 epon optical-transceiver current low-limit enable threshold 0 60
 
 
I hope this may help you !
Відредаговано sanitariu
Ссылка на сообщение
Поделиться на других сайтах
  В 02.10.2017 в 12:32, sanitariu сказав:

 

Hi,

I do not see anything strange. You are using multicasts.

May be try to raise storm filters.

Also on new versions you must enable this command:

"epon local-mac forward"

Although you do not have mac addresses like: X2:XX:XX:XX:XX:XX,X6:XX:XX:XX:XX:XX, XA:XX:XX:XX:XX:XX, XE:XX:XX:XX:XX:XX

Some day you can buy such onus and they will make disconnects. This is another BDCOM trick to try making their OLTs work only with

bdcom onus.

Also this is the correct oams:

epon oam-version 1 0x30

epon oam-version 2 0x21
epon oam-version 3 0x20
 
You can change them.
You can try to enable the following on the Epon interfaces:
 
 epon fec-rx
 epon fec-tx
 epon optical-transceiver power-tx high-limit enable threshold 70 30
 epon optical-transceiver power-tx low-limit enable threshold 20 20
 epon optical-transceiver temperature high-limit enable threshold 500 400
 epon optical-transceiver temperature low-limit enable threshold -1280 -400
 epon optical-transceiver voltage high-limit enable threshold 30 25
 epon optical-transceiver voltage low-limit enable threshold 0 10
 epon optical-transceiver current high-limit enable threshold 1310 800
 epon optical-transceiver current low-limit enable threshold 0 60
 
 
I hope this may help you !

 

 

Не. Не помогает ничего из перечисленного. Всё равно голова отваливает все активные EPON-интерфейсы и, судя по логам, ребутится. Хотя аптайм показывает, что не ребутится.

Відредаговано Fallen_Grayswandir
Ссылка на сообщение
Поделиться на других сайтах
  В 04.10.2017 в 13:44, sanitariu сказав:

Hm, then it seems something wrong with OLT ?

Do you have that problem only on one OLT device or all the same ?

 

I have this problem on all OLTs. But, when I upgrade firmware from 42425 to 43480, problem remains only on one OLT, where there are 4 V-Solution ONUs.

I'll try to replace it and look, the problem remains or not.

Ссылка на сообщение
Поделиться на других сайтах
  • 2 weeks later...

Ребята скажите а у всех пинги скачут до ОЛТ под нагрузкой на 3310с? Стоит один 3310с и второй b, c включен каскадом в b. До b пинг в норме, до с в среднем 100мс.

Ссылка на сообщение
Поделиться на других сайтах

Подскажите, как можно на голове потушить конкретную onu, при условии, что на голове не настроена никакая аутентификация onu'шек.

Ссылка на сообщение
Поделиться на других сайтах
  В 24.10.2017 в 07:53, Fallen_Grayswandir сказав:

Подскажите, как можно на голове потушить конкретную onu, при условии, что на голове не настроена никакая аутентификация onu'шек.

config
interface epon0/1:17
epon onu port 1 ctc shutdown # отключить 1 порт на 17 ONU
no epon onu port 1 ctc shutdown # включить 1 порт на 17 ONU
Ссылка на сообщение
Поделиться на других сайтах
  В 24.10.2017 в 08:09, Anatoliy сказав:

 

  В 24.10.2017 в 07:53, Fallen_Grayswandir сказав:

Подскажите, как можно на голове потушить конкретную onu, при условии, что на голове не настроена никакая аутентификация onu'шек.

config
interface epon0/1:17
epon onu port 1 ctc shutdown # отключить 1 порт на 17 ONU
no epon onu port 1 ctc shutdown # включить 1 порт на 17 ONU

 

 

Благодарствую. это лан-порт потушит, а мне именно пон нужно, чтобы на онушке loss горел. Ну и так сойдёт.

Відредаговано Fallen_Grayswandir
Ссылка на сообщение
Поделиться на других сайтах
  В 24.10.2017 в 16:29, Fallen_Grayswandir сказав:

 

  В 24.10.2017 в 08:09, Anatoliy сказав:

 

  В 24.10.2017 в 07:53, Fallen_Grayswandir сказав:

Подскажите, как можно на голове потушить конкретную onu, при условии, что на голове не настроена никакая аутентификация onu'шек.

config

interface epon0/1:17

epon onu port 1 ctc shutdown # отключить 1 порт на 17 ONU

no epon onu port 1 ctc shutdown # включить 1 порт на 17 ONU

Благодарствую. это лан-порт потушит, а мне именно пон нужно, чтобы на онушке loss горел. Ну и так сойдёт.

Будет loss гореть у клиента.

Ссылка на сообщение
Поделиться на других сайтах
  В 24.10.2017 в 17:27, Anatoliy сказав:

 

  В 24.10.2017 в 16:29, Fallen_Grayswandir сказав:

 

  В 24.10.2017 в 08:09, Anatoliy сказав:

 

  В 24.10.2017 в 07:53, Fallen_Grayswandir сказав:

Подскажите, как можно на голове потушить конкретную onu, при условии, что на голове не настроена никакая аутентификация onu'шек.

config

interface epon0/1:17

epon onu port 1 ctc shutdown # отключить 1 порт на 17 ONU

no epon onu port 1 ctc shutdown # включить 1 порт на 17 ONU

Благодарствую. это лан-порт потушит, а мне именно пон нужно, чтобы на онушке loss горел. Ну и так сойдёт.
Будет loss гореть у клиента.
С чего бы ему гореть? Вы же просто uni порт сложили. Відредаговано Den_LocalNet
Ссылка на сообщение
Поделиться на других сайтах
  В 05.10.2017 в 07:48, Fallen_Grayswandir сказав:

 

  В 04.10.2017 в 13:44, sanitariu сказав:

Hm, then it seems something wrong with OLT ?

Do you have that problem only on one OLT device or all the same ?

 

I have this problem on all OLTs. But, when I upgrade firmware from 42425 to 43480, problem remains only on one OLT, where there are 4 V-Solution ONUs.

I'll try to replace it and look, the problem remains or not.

 

 

Заменили наконец-то все V-Solution ОНУшки. Не помогло. :( Всё равно  головы ребутятся. Одна чаще, другая реже...

Ссылка на сообщение
Поделиться на других сайтах
  • 2 weeks later...

Доброго дня. Не працює NTP на BDCOM P3310C Software, Version 10.1.0E Build 36957

 

time-zone Kiev 3 0
ntp master primary
ntp server 62.149.2.62

 

show ntp     

Time-zone: GMT+3:00, Kiev
Current time: 1970-07-18 23:32:31

Clock Status: synchronized
Clock Stratum: 1
Leap Indicator: 0
Reference ID: LOCL
Clock Jitter: 0.000000
Clock Precision: -7
Clock Offset: 0.000 ms
Root Delay: 0.000 ms
Root Dispersion: 0.000 ms
Packets Sent: 0
Packets Received: 0 (bad version: 0)
Reference Time: 1970-01-01 00:00:00
Last Update Time: 1970-01-01 00:00:00

 

 

 

Пробував -

time-zone Kyiv 2 0
ntp query-interval 60
ntp server 62.149.2.62 version 4
ntp peer 62.149.2.62 version 4   не допомагає.

Ссылка на сообщение
Поделиться на других сайтах

Я ж тебе говорил - земля проклятая, а ты "руки из жопы, руки из жопы"

:D :D

http://joxi.ru/p27KDg9S0jDYv2

Тока сорян, таймзону не менял и не настраивал автопереход зима\лето. Как бы нах не нужно :)

Ссылка на сообщение
Поделиться на других сайтах

Создайте аккаунт или войдите в него для комментирования

Вы должны быть пользователем, чтобы оставить комментарий

Создать аккаунт

Зарегистрируйтесь для получения аккаунта. Это просто!

Зарегистрировать аккаунт

Вхід

Уже зарегистрированы? Войдите здесь.

Войти сейчас
  • Зараз на сторінці   0 користувачів

    Немає користувачів, що переглядають цю сторінку.

  • Схожий контент


×
×
  • Створити нове...