Ajar 93 Posted 2013-01-21 14:50:36 Share Posted 2013-01-21 14:50:36 Нет , но в теории должен потянуть он же похож на 48si и 7i ... а они тянуть 200000 или 400000 маршрутов , не помню точно сколько. Воть нашел http://www.filibeto.org/sun/lib/nonsun/extreme/Relnote_621b20rev2.pdf Link to post Share on other sites
Ajar 93 Posted 2013-01-21 14:56:09 Share Posted 2013-01-21 14:56:09 6.21 EOS BGP routes—BlackDiamond, Summit 7i and Alpine 3808/3804 Maximum number of routes contained in the BGP 400,000 route table BGP routes—Summit 1i, Summit 5i, and Summit 48i Maximum number of routes contained in the BGP 200,000 route table Link to post Share on other sites
prototip 286 Posted 2013-01-21 15:07:15 Share Posted 2013-01-21 15:07:15 Ну эт в рекламных буклетах .... На черном диаманте самита по этой причине "мозги управления" со временем появились другие , более шустрые , да и на ссиське та же картина маслом . А вот на альпине 3804 или еже с ней мозг только один и как я понимаю ему сним жить тяжело . Колличество маршрутов на таких старых тазах космическое , однако много чего обрабатывается мозгом , а нынче трафик совсем не тот который был десять лет назад , когда эти шелезяки были актуальны . Я просто хотел услышать отзыв реального пользователя - железка довольно дешевая , на ебее модуля вообще сущие копейки стоят , единственный минус этого таза наверное еще и колличество киловатт часов , которые он успешно превращает тепло . Такие тазики как сиська 6500 вролне можно ставить в систему отопления здания малехо доработав ее или женившись на кривой дочери начальника облэнерго . Link to post Share on other sites
KaYot 3,732 Posted 2013-01-22 09:18:54 Share Posted 2013-01-22 09:18:54 Практически на все железо со временем выходят более навороченные модули управления. Просто по той причине, что стоящий там pentium3 1.0Ghz больше не выпускается, и производителю стали отгружать новую ревизию, с теми же тепловыми/электрическими параметрами, но на 1.6Ghz Приходится делать наклейку sup5000zxe_ver3.0 А вот зачем коммутатору мозги - сложный вопрос, тем более под BGP. Разве что скорость построения таблиц меняется, а на трафик плевать. Link to post Share on other sites
prototip 286 Posted 2013-01-23 12:29:40 Share Posted 2013-01-23 12:29:40 Хех барин зачем кому мозги ..... Если бы так все было просто ... Я вообще вопрошал по поводу Alpine 3800 от самита у кого такое живет , железка старая , фабрика там скромная , мозг там только одного вида , маршрутов там в достатке , для небольшой сетки вроде как неплохой вариант , как к примеру 3804 . Из минусов 10г нет и не будет в отличи от сиськи 6500 , правда на 1г есть очень не дорогие платки по 16 сфп , ну и насколько я понял только Extremware . Link to post Share on other sites
Ajar 93 Posted 2013-01-23 14:51:47 Share Posted 2013-01-23 14:51:47 Если уж очень хочется alpine - возьмите на тест у продавца . Link to post Share on other sites
skybetik 134 Posted 2014-12-21 22:43:42 Share Posted 2014-12-21 22:43:42 Ребзя посоветуйте не дорогой l3 для bgp принятия 2 default inet +ua-ix ,ws-c3550-12t не справляется ( Link to post Share on other sites
l1ght 377 Posted 2014-12-21 23:59:53 Share Posted 2014-12-21 23:59:53 3750? Трохи більше маршрутів Link to post Share on other sites
loki 86 Posted 2014-12-22 02:24:26 Share Posted 2014-12-22 02:24:26 Практически на все железо со временем выходят более навороченные модули управления. Просто по той причине, что стоящий там pentium3 1.0Ghz больше не выпускается, и производителю стали отгружать новую ревизию, с теми же тепловыми/электрическими параметрами, но на 1.6Ghz Приходится делать наклейку sup5000zxe_ver3.0 А вот зачем коммутатору мозги - сложный вопрос, тем более под BGP. Разве что скорость построения таблиц меняется, а на трафик плевать. Чтоб больше не писать ахинею, про "мозги" коммутатора, предлагаю послушать вот этот подскат : http://linkmeup.ru/blog/124.html Link to post Share on other sites
Ruslik 27 Posted 2014-12-22 02:33:54 Share Posted 2014-12-22 02:33:54 Ребзя посоветуйте не дорогой l3 для bgp принятия 2 default inet +ua-ix ,ws-c3550-12t не справляется ( Juniper EX3200, 16к префиксов. Link to post Share on other sites
Link_x 47 Posted 2014-12-22 08:35:18 Share Posted 2014-12-22 08:35:18 3750-12s. У него вроде больше маршрутов чем у обычной 3750. Link to post Share on other sites
KaYot 3,732 Posted 2014-12-22 08:49:14 Share Posted 2014-12-22 08:49:14 Ребзя посоветуйте не дорогой l3 для bgp принятия 2 default inet +ua-ix ,ws-c3550-12t не справляется (А что с 3550 не так? Память заканчивается? "Недорогих" под принятие современного ua-ix нет, нужно 16к+ маршрутов. Сейчас один из магистралов мне наливает 15832 префиксов, а значит и 16к уже не особо канает. Могу порекомендовать cisco WS-C4948 и WS-C4948-10GE с 32к маршрутов. Стоит 4948-10GE у нас, работает идеально, денег на ебее стоит $1к. Без 10G еще на пару сотен меньше. Link to post Share on other sites
alfko 15 Posted 2014-12-22 09:05:25 Share Posted 2014-12-22 09:05:25 Juniper EX3200, 16к префиксов. Я даже не знаю под что его хватит. В нашем случае: Active/holddown/hidden UA.inet.0 19751/0/2 Ребзя посоветуйте не дорогой l3 для bgp принятия 2 default inet +ua-ix ,ws-c3550-12t не справляется ( Могу Вам предложить M7i с дополнительной картой, по дешевке. Спокойно жует 3 фулвью. Link to post Share on other sites
Ajar 93 Posted 2014-12-22 10:02:55 Share Posted 2014-12-22 10:02:55 Ребзя посоветуйте не дорогой l3 для bgp принятия 2 default inet +ua-ix ,ws-c3550-12t не справляется (А что с 3550 не так? Память заканчивается?"Недорогих" под принятие современного ua-ix нет, нужно 16к+ маршрутов. Сейчас один из магистралов мне наливает 15832 префиксов, а значит и 16к уже не особо канает. Могу порекомендовать cisco WS-C4948 и WS-C4948-10GE с 32к маршрутов. Стоит 4948-10GE у нас, работает идеально, денег на ебее стоит $1к. Без 10G еще на пару сотен меньше. Отличный бюджетный и надежный вариант. Link to post Share on other sites
NiTr0 585 Posted 2014-12-22 10:15:24 Share Posted 2014-12-22 10:15:24 Можно попробоватьбгп принимать на писюке, агрегировать префиксы, и скармливать результат в 3550... Link to post Share on other sites
Kto To 602 Posted 2014-12-22 11:12:59 Share Posted 2014-12-22 11:12:59 Из недорогих только 3550. Была еще давно у нас (на заре сетестроения) 2948G-L3 Отлично лопатила гиг вход гиг выход. Были там нюансы с номерам вланов выше 1200 помоему. Можете посмотреть в сторону этой железяки. Из не циско - могу посоветовать офигенное решение: FESX424HF+1XG-PREM 24 sfp, 4 комбо, 1 xfp (есть вариации 2XG, 2 xfp) базовых 128мб памяти (расширяется планками до 512) фулл л3 вливается 80к! маршрутов шейпинг/полисинг на портах имеет два блока питания в принципе больше ничего не использовали из функционала. на ебей нашел цену в 330$ хотя другое предложение в 950$ решайте сами. Link to post Share on other sites
skybetik 134 Posted 2014-12-24 14:43:03 Share Posted 2014-12-24 14:43:03 как посмотреть сколько маршрутов 3550 сможет прожувать?? тут такое дело налили 1 defolt и 1 UA-IX Порядка 17500 сетей и 3550 12Т ушол в ступр проц 80% sh sdm prefer The current template is the default template. The selected template optimizes the resources in the switch to support this level of features for 16 routed interfaces and 1K VLANs. number of unicast mac addresses: 6K number of igmp groups: 6K number of qos aces: 2K number of security aces: 2K number of unicast routes: 12K number of multicast routes: 6K sh sdm prefer routing routing template: The selected template optimizes the resources in the switch to support this level of features for 16 routed interfaces and 1K VLANs. number of unicast mac addresses: 6K number of igmp groups: 6K number of qos aces: 1K number of security aces: 1K number of unicast routes: 24K number of multicast routes: 6K Link to post Share on other sites
KaYot 3,732 Posted 2014-12-24 14:50:04 Share Posted 2014-12-24 14:50:04 Дык все верно, сейчас у вас стоит default template и в нем влезает 12к маршрутов. От 17 свич конечно же тошнит.. Переключите в routing template и все полетит(sdm prefer routing). Link to post Share on other sites
skybetik 134 Posted 2014-12-24 14:52:20 Share Posted 2014-12-24 14:52:20 KaYotНаведи на мысл как ,я не силен в цыске Link to post Share on other sites
KaYot 3,732 Posted 2014-12-24 14:54:32 Share Posted 2014-12-24 14:54:32 KaYot Наведи на мысл как ,я не силен в цыске В режиме конфигурации так и пиши, sdm prefer routing, сохраниться и в ребут. После этого show sdm prefer будет показывать актуальный темплейт. Link to post Share on other sites
Ajar 93 Posted 2014-12-24 15:52:23 Share Posted 2014-12-24 15:52:23 как посмотреть сколько маршрутов 3550 сможет прожувать?? тут такое дело налили 1 defolt и 1 UA-IX Порядка 17500 сетей и 3550 12Т ушол в ступр проц 80% sh sdm prefer The current template is the default template. The selected template optimizes the resources in the switch to support this level of features for 16 routed interfaces and 1K VLANs. number of unicast mac addresses: 6K number of igmp groups: 6K number of qos aces: 2K number of security aces: 2K number of unicast routes: 12K number of multicast routes: 6K sh sdm prefer routing routing template: The selected template optimizes the resources in the switch to support this level of features for 16 routed interfaces and 1K VLANs. number of unicast mac addresses: 6K number of igmp groups: 6K number of qos aces: 1K number of security aces: 1K number of unicast routes: 24K number of multicast routes: 6K conf t sdm pre rou exit reload yes Link to post Share on other sites
skybetik 134 Posted 2014-12-24 15:55:40 Share Posted 2014-12-24 15:55:40 *Mar 1 00:02:05.479: %BGP-5-ADJCHANGE: neighbor 81.25.221.161 Up *Mar 1 00:03:19.923: %SYS-2-MALLOCFAIL: Memory allocation of 65536 bytes failed from 0x129A40C, alignment 0 Pool: Processor Free: 106168 Cause: Memory fragmentation Alternate Pool: None Free: 0 Cause: No Alternate pool -Process= "IP RIB Update", ipl= 0, pid= 125 -Traceback= 12865E4 1288B04 1288E14 129A410 129B06C B575BC B4E518 B4EAA0 B4EE00 B4F238 B4F708 F4E60C F4E774 EE4040 E90DA8 E90EA4 *Mar 1 00:03:20.519: %COMMON_FIB-3-NOMEM: Memory allocation failure for prefix in IPv4 CEF [0x00B57684] (fatal) (4985 subsequent failures). *Mar 1 00:03:20.519: %COMMON_FIB-4-DISABLING: IPv4 CEF is being disabled due to a fatal error. *Mar 1 00:04:17.359: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:05:17.379: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:06:17.403: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:07:17.427: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:08:17.447: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:09:17.471: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:10:17.491: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:11:17.523: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:12:17.551: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:13:17.583: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:14:17.615: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:15:17.651: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:16:17.679: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:17:17.711: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:18:03.043: %SYS-2-MALLOCFAIL: Memory allocation of 10000 bytes failed from 0x129A40C, alignment 0 Pool: Processor Free: 151552 Cause: Memory fragmentation Alternate Pool: None Free: 0 Cause: No Alternate pool -Process= "CEF: IPv4 process", ipl= 0, pid= 157 -Traceback= 12865E4 1288B04 1288E14 129A410 129B06C 5F0BEC 5F34D4 B9F8A8 B4A0EC B63EE0 B64068 B4ECD8 B4EE00 B4F238 B4F708 F4E9EC *Mar 1 00:18:03.631: %COMMON_FIB-3-NOMEM: Memory allocation failure for prefix in IPv4 CEF [0x00B57684] (fatal) (0 subsequent failures). *Mar 1 00:18:03.631: %COMMON_FIB-4-DISABLING: IPv4 CEF is being disabled due to a fatal error. *Mar 1 00:18:06.599: %SYS-2-CHUNKEXPANDFAIL: Could not expand chunk pool for messages. No memory available -Process= "Chunk Manager", ipl= 4, pid= 1 -Traceback= 1285C30 514550 50AFC8 *Mar 1 00:18:17.747: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed] Просто беда Link to post Share on other sites
bit 58 Posted 2014-12-24 16:10:18 Share Posted 2014-12-24 16:10:18 Если совсем сложно с колличеством преффиксов, принимайте не меньше /23 ... /22 ... /21 Немного кривовато. Часть выйдет в сторону дефолта, ну то таке. Link to post Share on other sites
KaYot 3,732 Posted 2014-12-24 16:54:56 Share Posted 2014-12-24 16:54:56 *Mar 1 00:02:05.479: %BGP-5-ADJCHANGE: neighbor 81.25.221.161 Up *Mar 1 00:03:19.923: %SYS-2-MALLOCFAIL: Memory allocation of 65536 bytes failed from 0x129A40C, alignment 0 Pool: Processor Free: 106168 Cause: Memory fragmentation Alternate Pool: None Free: 0 Cause: No Alternate pool -Process= "IP RIB Update", ipl= 0, pid= 125 -Traceback= 12865E4 1288B04 1288E14 129A410 129B06C B575BC B4E518 B4EAA0 B4EE00 B4F238 B4F708 F4E60C F4E774 EE4040 E90DA8 E90EA4 *Mar 1 00:03:20.519: %COMMON_FIB-3-NOMEM: Memory allocation failure for prefix in IPv4 CEF [0x00B57684] (fatal) (4985 subsequent failures). *Mar 1 00:03:20.519: %COMMON_FIB-4-DISABLING: IPv4 CEF is being disabled due to a fatal error. *Mar 1 00:04:17.359: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:05:17.379: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:06:17.403: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:07:17.427: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:08:17.447: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:09:17.471: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:10:17.491: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:11:17.523: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:12:17.551: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:13:17.583: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:14:17.615: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:15:17.651: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:16:17.679: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:17:17.711: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed]" *Mar 1 00:18:03.043: %SYS-2-MALLOCFAIL: Memory allocation of 10000 bytes failed from 0x129A40C, alignment 0 Pool: Processor Free: 151552 Cause: Memory fragmentation Alternate Pool: None Free: 0 Cause: No Alternate pool -Process= "CEF: IPv4 process", ipl= 0, pid= 157 -Traceback= 12865E4 1288B04 1288E14 129A410 129B06C 5F0BEC 5F34D4 B9F8A8 B4A0EC B63EE0 B64068 B4ECD8 B4EE00 B4F238 B4F708 F4E9EC *Mar 1 00:18:03.631: %COMMON_FIB-3-NOMEM: Memory allocation failure for prefix in IPv4 CEF [0x00B57684] (fatal) (0 subsequent failures). *Mar 1 00:18:03.631: %COMMON_FIB-4-DISABLING: IPv4 CEF is being disabled due to a fatal error. *Mar 1 00:18:06.599: %SYS-2-CHUNKEXPANDFAIL: Could not expand chunk pool for messages. No memory available -Process= "Chunk Manager", ipl= 4, pid= 1 -Traceback= 1285C30 514550 50AFC8 *Mar 1 00:18:17.747: %FIB-2-FIBDOWN: CEF has been disabled due to a low memory condition. It can be re-enabled by configuring "ip cef [distributed] Просто беда Ну а это уже другая беда 3550, физически мало памяти. Решения нормального вроде как нет, разве что перебирать прошивки в поисках легковесной. Link to post Share on other sites
azazelo 23 Posted 2014-12-24 19:52:18 Share Posted 2014-12-24 19:52:18 Ребзя посоветуйте не дорогой l3 для bgp принятия 2 default inet +ua-ix ,ws-c3550-12t не справляется (А что с 3550 не так? Память заканчивается?"Недорогих" под принятие современного ua-ix нет, нужно 16к+ маршрутов.Сейчас один из магистралов мне наливает 15832 префиксов, а значит и 16к уже не особо канает.Могу порекомендовать cisco WS-C4948 и WS-C4948-10GE с 32к маршрутов. Стоит 4948-10GE у нас, работает идеально, денег на ебее стоит $1к. Без 10G еще на пару сотен меньше. Бывает ли такой свитч с меньшим количеством портов? 48 совершенно ни к чему. Link to post Share on other sites
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now