Jump to content

ePMP Cambium


Recommended Posts

  • Replies 1.4k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Popular Posts

Всё. Я забухал.

Причём толерантность в первую очередь от него и исходит...

да вы просто ХАМЛО! вам это ещё никто не говорил ? удивительно что вообще кто-то ещё с вами имеет дело!

Posted Images

Прошивка 3.2.1

Причем зависает LAN порт с двух сторон как на Master так и на Slave железо с двух сторон разное.

На Master помагает выключить и включить порт на комутаторе, а на Slave перезагрузка Cambium.

Edited by olsasha
Link to post
Share on other sites

Прошивка 3.2.1

Причем зависает LAN порт с двух сторон как на Master так и на Slave железо с двух сторон разное.

На Master помагает выключить и включить порт на комутаторе, а на Slave перезагрузка Cambium.

Такое раньше не встречалось. Да  еще одновременно на разных  девайсах. Это только в режиме ePTP?  Свич одинаковый ? Какой именно?

Edited by Alver
Link to post
Share on other sites

Режим TDD. Управляемые свичи D-Link разных моделей.

 Переведите линк в режим ePTP.  Попробуйте временно заменить длинк на что то другое. И попробуйте разные конфигурации порта на свиче и Камбиум, обратите внимание  на Flow Control порта  свича. 

Link to post
Share on other sites

Сегодня зависла web-морда на ePMP1000 (AP TDD PTP, v3.2), при заходе на устройство прогружается только шапка страницы, кнопка reboot device не срабатывает. По телнету на команду "reboot" получаю ответ "Timeout: No Response from localhost". На клиента заходит нормально, сам линк работает нормально. Лезть дергать точку доступа из розетки?

Link to post
Share on other sites

заметил баг если ранее был залит конфиг  затем  прошили v3.2 то начинается "своя жизнь у точек" помогает резет вручную, (побывал резетнуть точку как показано в мануале с блока питания то это это каке-то танцы с бубном раза с 50-го получилось,   неужели так трудно кнопочку как у ubnt reset сделать на б\п?)

Link to post
Share on other sites

 

 

Сегодня зависла web-морда на ePMP1000 (AP TDD PTP, v3.2), при заходе на устройство прогружается только шапка страницы, кнопка reboot device не срабатывает. По телнету на команду "reboot" получаю ответ "Timeout: No Response from localhost". На клиента заходит нормально, сам линк работает нормально. Лезть дергать точку доступа из розетки?

Этот  баг  появился  где то в 3.1 или позже. Обновите прошивку до 3.2.2

Link to post
Share on other sites

 

Сегодня зависла web-морда на ePMP1000 (AP TDD PTP, v3.2), при заходе на устройство прогружается только шапка страницы, кнопка reboot device не срабатывает. По телнету на команду "reboot" получаю ответ "Timeout: No Response from localhost". На клиента заходит нормально, сам линк работает нормально. Лезть дергать точку доступа из розетки?

Этот  баг  появился  где то в 3.1 или позже. Обновите прошивку до 3.2.2

 

чтобы обновиться надо залезть на вышку и резетнуть точку так-как с бп можно ребутить до нескольких часов! 

Link to post
Share on other sites

Т.е. нужно именно сбросить настройки, настроить заново и обновить прошивку? Без сброса текущих настроек никак не обойтись?

Link to post
Share on other sites

Т.е. нужно именно сбросить настройки, настроить заново и обновить прошивку? Без сброса текущих настроек никак не обойтись?

Надо сбросить  по питанию.  Сбрасывать  настройки в дефолт необязательно. Но и для этого не надо добираться до кнопки ресет, можно делать через поверцикл ( если он не запрещен на устройстве), но надо точно соблюсти алгоритм.  

Link to post
Share on other sites

Это оно?

 

Procedure:
1. Remove the Ethernet cable from PoE jack of the power supply for at least 10 seconds.
2. Reconnect the Ethernet cable to re-supply power to the ePMP device for 3-5 seconds and disconnect cable to power off the ePMP device for 3-5 seconds. (1st power cycle)
3. Reconnect the Ethernet cable to re-supply power to the ePMP device for 3-5 seconds and disconnect cable to power off the ePMP device for 3-5 seconds. (2nd power cycle)
4. Reconnect the Ethernet cable to re-supply power to the ePMP device for 3-5 seconds and disconnect cable to power off the ePMP device for 3-5 seconds. (3rd power cycle)
5. Reconnect the Ethernet cable to re-supply power to the ePMP device for 3-5 seconds and disconnect cable to power off the ePMP device for 3-5 seconds. (4th power cycle)
6. Reconnect the Ethernet cable to re-supply power to the ePMP device for at least 30 seconds and allow it to go through the boot up procedure (Note: Device will go through an additional reset automatically). This will reset the current configuration files to factory default configuration (e.g. IP addresses, Device mode, RF configuration etc.). The device can be pinged from a PC to check if boot up is complete (Successful ping replies indicates boot up is complete).
7. Access the ePMP device using the default IP address of 192.168.0.1 (AP) or 192.168.0.2 (SM).

Edited by molecul
Link to post
Share on other sites

Это оно?

 

Procedure:

1. Remove the Ethernet cable from PoE jack of the power supply for at least 10 seconds.

2. Reconnect the Ethernet cable to re-supply power to the ePMP device for 3-5 seconds and disconnect cable to power off the ePMP device for 3-5 seconds. (1st power cycle)

3. Reconnect the Ethernet cable to re-supply power to the ePMP device for 3-5 seconds and disconnect cable to power off the ePMP device for 3-5 seconds. (2nd power cycle)

4. Reconnect the Ethernet cable to re-supply power to the ePMP device for 3-5 seconds and disconnect cable to power off the ePMP device for 3-5 seconds. (3rd power cycle)

5. Reconnect the Ethernet cable to re-supply power to the ePMP device for 3-5 seconds and disconnect cable to power off the ePMP device for 3-5 seconds. (4th power cycle)

6. Reconnect the Ethernet cable to re-supply power to the ePMP device for at least 30 seconds and allow it to go through the boot up procedure (Note: Device will go through an additional reset automatically). This will reset the current configuration files to factory default configuration (e.g. IP addresses, Device mode, RF configuration etc.). The device can be pinged from a PC to check if boot up is complete (Successful ping replies indicates boot up is complete).

7. Access the ePMP device using the default IP address of 192.168.0.1 (AP) or 192.168.0.2 (SM).

Оно.  Но соблюдать нужно все точно, как написано. 

Link to post
Share on other sites
  • 1 month later...

 

 

Таких случаев с МТ не было ни разу.

А у моих заказчиков -операторов ( которых несколько сотен только  в Украине ) , которые работают и с Камбиум и ubnt/mt таких случаев ( неподнятия  и МТ и ubnt по неизвестным причинам) -сотни.  Только по гарантии их ( МТ  и  ubnt) зачастую  некому , да и незачем ( нет смысла) отправлять.

 

 

У нас тысячи МТ, камбиума 4шт. было, с МТ ни разу такого не было. Сказки другим плиз рассказывайте.

 

 

Вячеслав в который раз идет лесом...

 

По теме, парк из более чем 1000 МТ/UBNT, поставил и забыл, одна железка стояла без питания лет пять. чел уезжал, приехал, подключили - пашет )))

 

Основная поломка - грозы, по прошивке, было два случая слета...

Link to post
Share on other sites
  • 7 months later...

Оборудование  Cambium ePMP 2000, Force 180, Force 190, Force 200 внесено в Реестр  РЭС для вновь открытого для лицензирования диапазона частот 5670-5725 МГц.

Link to post
Share on other sites
  • 7 months later...

Есть мост на Cambium ePMP 1000 force 200 расстояние между точками 8км сигнал -71- -65dBm при тестировании Tools -> Wireless Link Test 

Packet Size Small (128 bytes) показывает Downlink 30.656 Mbps/Uplink 23.243 Mbps

Packet Size Medium (800 bytes) показывает Downlink 65.305 Mbps/Uplink 73.046 Mbps

Packet Size Large (1500 bytes) показывает Downlink 74.676 Mbps/Uplink 90.126 Mbps

Раздающая антена:

Radio Mode:Access Point

Access Point Mode: ePTP Master

Max Range:24

Channel Bandwidth:40

Frequency Carrier:5300

Transmitter Output Power:30

Antenna Gain:40

Subscriber Module Target Receive Level:60

Антена со второй стороны:

Radio Mode:Subscriber Module

Subscriber Module Mode:ePTP Slave

Transmitter Output Power:30

Antenna Gain:40

Network Entry RSSI Threshold:100

Network Entry SNR Threshold:0

Forced Sector Antenna:Disabled

 

Software Version 3.0.1

Firmware Version U-Boot 9342_PX 1.1.4.e (Sep 21 2016 - 11:55:11)

Подскажите есть ли какие тонкости настройки, прошивки и тд. что бы повысить скорость? 

 

 

Link to post
Share on other sites
1 час назад, Hasta84 сказал:

Есть мост на Cambium ePMP 1000 force 200 расстояние между точками 8км сигнал -71- -65dBm при тестировании Tools -> Wireless Link Test 

Packet Size Small (128 bytes) показывает Downlink 30.656 Mbps/Uplink 23.243 Mbps

Packet Size Medium (800 bytes) показывает Downlink 65.305 Mbps/Uplink 73.046 Mbps

Packet Size Large (1500 bytes) показывает Downlink 74.676 Mbps/Uplink 90.126 Mbps

Раздающая антена:

Radio Mode:Access Point

Access Point Mode: ePTP Master

Max Range:24

Channel Bandwidth:40

Frequency Carrier:5300

Transmitter Output Power:30

Antenna Gain:40

Subscriber Module Target Receive Level:60

Антена со второй стороны:

Radio Mode:Subscriber Module

Subscriber Module Mode:ePTP Slave

Transmitter Output Power:30

Antenna Gain:40

Network Entry RSSI Threshold:100

Network Entry SNR Threshold:0

Forced Sector Antenna:Disabled

 

Software Version 3.0.1

Firmware Version U-Boot 9342_PX 1.1.4.e (Sep 21 2016 - 11:55:11)

Подскажите есть ли какие тонкости настройки, прошивки и тд. что бы повысить скорость? 

 

 

выбросить эту задрочь нафиг и поставить толковую железку вроде Mimosa C5c

  • Like 1
Link to post
Share on other sites
1 минуту назад, zulu_Radist сказал:

с сигналом у вас проблемы, или нет прямой видимости или юстировка не произведена должным образом

ну это как само собой подразумевающееся

Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content


×
×
  • Create New...